Lakeshore 84032-FI Installation Manual Download

Page: 11 / 11

Revision 1.1

P/N 119-845

IV.

Testing and Verification

Refer to the user’s manual for gate bias setup. Contact Lake Shore to receive the latest user manual for
your configuration and software version.

Service

The most direct and efficient means of contacting Lake Shore is to complete the online service request
form at

http://www.lakeshore.com/service/Pages/default.aspx

. Provide a detailed description of the

problem and the required contact information. You will receive a response within 24 hours, or the next
business day in the event of weekends or holidays.

If you wish to contact Systems Service by mail or telephone, use the following:

Lake Shore Cryotronics, Inc.
575 McCorkle Blvd.
Westerville, Ohio 43082 USA
Phone: 614-891-2243 (option 6)
Fax: 614-818-1608
e-mail:

sysservice@lakeshore.com

Summary of Contents for 84032-FI












Search results

Summary of Contents for 84032-FI

Reviews:

Related manuals for 84032-FI

Brands by name

Popular brands

Lakeshore 84032-FI, Installation Manual

Search results

Summary of Contents for 84032-FI

Reviews:

Related manuals for 84032-FI

Brands by name

Popular brands