Lakeshore 84032-FI Installation Manual Download | Manualshive

Page: 6 / 11

background image

Revision 1.1

P/N 119-845

6

Mount the Instrument

The Keithley 6487 should be installed using one of the provided rack mount kits.

The half rack mount kit contains mounting ears, panel, handles (optional), and screws that adapt the
front panel to fit into an 88.9 mm (3.5 in) tall full rack space. Refer to Figure 4 for installation details.

The dual half rack mount kit contains inner and outer mounting ears, handles (optional), and screws that
adapt the front panel to fit into an 88.9 mm (3.5 in) tall full rack space beside an existing instrument.
Refer to Figure 5 for installation details.

NOTE: Ensure that there is a 25 mm (1 in) clearance on both sides of the instrument after
rack mounting.

Figure 5:

Half rack mounting

Figure 6:

Dual half rack mounting

«
...
4
5
6
7
8
...
»

Summary of Contents for 84032-FI












Reviews:

No comments

Related manuals for 84032-FI

Brand: barrier Pages: 2

Brand: WamBam Pages: 16

Plain Jane Vinyl Gate

Brand: WamBam Pages: 29

KESWICK ZP19060

Brand: Zippity Pages: 12

Publifor 3D Pro XL

Brand: Betafence Pages: 10

Dreambaby Nelson F826

Brand: Tee-Zed Pages: 4

Brand: Jysk Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands