background image

Lambda Labs - Professional Acoustics                                                                                                                                                                   DH-18 Manual

5. Distance

 

Rod

 

With

 

the

 

use

 

of

 

the

 

built

 

in

 

Mounting

 

Flange,

 

a

 

Distance

 

Rod

 

with

 

M20

 

thread

 

can

 

be

 

mounted

 

on

 

the

 

DH-18.

 

www.lambda-labs.com 

 17

Note:

 

The

 

items

 

described

 

above

 

can

 

be

 

purchased

 

as:

 

Distance

 

Rod

 

V1:

 

Distance

 

Rod

 

with

 

splints

 

(Ring

 

Lock)

 

Distance

 

Rod

 

V2:

 

Distance

 

Rod

 

with

 

hand

 

crank

 

and

 

splints

 

(Ring

 

Lock)

 

 

Distance Rod V2

Danger:

 

When using a distance rod mounted on a subwoofer/s, the loudspeaker should never 

be  heavier  than  the  subwoofer/s  itself.  The  longer  the  distance  rod  is  extended,  the  greater  the 
counterweight  should  be.  Secure  the  subwoofers  to  each  other  with  straps  and/or  to  the  ground/
suitable  platforms!  Check  the  stability  in  every  case!  For  further  details,  refer  to  the  individual 
loudspeaker manuals as well.

 

DANGER!

Summary of Contents for DH-18
























Reviews: