background image

Printed 07-2001 

-14- 

Form No. M1-0002 

DEBRIS HAMPERS ARE NOT STORAGE CONTAINERS.  NEVER LEAVE FRESH GRASS CLIPPINGS OR OTHER 
ORGANIC MATTER IN HAMPER FOR ANY LENGTH OF TIME.  UNDER THE RIGHT CONDITIONS, SPONTANEOUS 
COMBUSTION, A FIRE GENERATING PROCESS WHICH OCCURS WITHOUT AN EXTERNAL SOURCE OF 
IGNITION, CAN OCCUR WITH THIS TYPE OF MATERIAL.  HAMPER CAN CATCH ON FIRE AND CAUSE SERIOUS 
PERSONAL INJURY. 

INSTRUCTOINS FOR ORDERING PARTS 

NOTE:  BE SURE TO SPECIFY COLOR (IF ANY) OF ANY PART YOU ORDER.  (MINIMUM ORDER 
CHARGE:  $15.00) 

TO ELIMINATE ERROR AND SPEEDY DELIVERY, FOLLOW THESE SUGGESTIONS. 

1. ADDRESS ALL PARTS ORDERS OR CORRESPONDENCE REGARDING SERVICE TO YOUR LOCAL

DEALER OR:

PARTS DEPARTMENT 

LAMBERT PRODUCTS, INC. 

P.O. BOX 278 

ANSONIA, OH 45303 

PHONE:  937-337-3641 FAX:  937-337-0755 
OR 

ORDER FROM OUR WEBSITE: 

WWW.LAMBERTMFG.COM 

2. PRINT OR TYPE YOUR NAME AND ADDRESS CLEARLY.

3. EXPLAIN WHERE AND HOW TO SHIP.

4. GIVE CORRECT MODEL NUMBER FROM OWNERS MANUAL OR PRODUCT AND STATE COLOR IF

PART IS PAINTED.

5. GIVE PART NUMBER, AS WELL AS A DESCRIPTION OF PART, AND THE QUANTITY YOU NEED OF

EACH PART.

6. INSPECT ALL SHIPMENTS YOU RECEIVE.  IF ANY PARTS ARE DAMAGED OR MISSING, FILE A

CLAIM WITH THE CARRIER BEFORE ACCEPTING.

7. PARTS WILL BE SHIPPED IMMEDIATELY UPON RECEIPT OF YOUR ORDER.  FOR YOUR

CONVIENENCE, WE ACCEPT MASTERCARD, VISA AND DISCOVER.  IF USING CREDIT CARD,
PLEASE GIVE FULL NAME ON CARD, CARD NUMBER AND EXPIRATION DATE OF CARD.

STORAGE

 

CLEAN HAMPER TO REMOVE CLIPPINGS AND DEBRIS.  HAMPER CAN BE REMOVED FOR STORAGE 
MOVE LEFT HAND AND RIGHT HAND CLIP HOOKS REARWARD AND REMOVE HAMPER ROD FROM 
NOTCHES IN HAMPER SUPPORT (FIG. 13).  WIPE DIRT AND GREASE FROM CHASIS.  REPAINT 
SCRATCHED AREAS AND COAT METAL PARTS WITH OIL TO PREVENT RUST.  CHECK SWEEPER 
PARTS FOR WEAR AND REPLACE PARTS AS NECESSARY.  STORE SWEEPER IN A DRY AREA OUT 
OF DIRECT SUNLIGHT. 

Summary of Contents for TW31CS















Reviews: