background image

18

GB

The “CE” marking indicates that the units comply with the requirements of the applicable European 

directives.

In particular, this unit complies with the following EEC directives:

• Low Voltage Directive 2006/95/CE

• Electromagnetic Compatibility Directive 2004/108/CE

 CERTIFICATION

 INDEX

Operating instructions   

 

19

Installation 

 

 

 

24

Service and maintenace  

 

27

Techincal data and characteristics 

31

• Carefully read the instructions in this handbook, since they provide important information on safe installation, use and 

maintenance.

• The instruction handbook is an integral part of the product and must be carefully kept by the user for future referen

-

ce.

• Installation and maintenance must be carried out by professionaly qualified personnel, in compilance with current 

regulations and the manufaturer’s instructions.

• Incorrect installation or poor maintenance can result in damage or injury. The manufacturer declines any liability for 

damege caused by incorrect installation and use or failure to follow its instructions.

• Before carrying out any cleaning or maintenance operation, disconnet the unit from power supply by means of the 

switch and/or the special cutoff devices.

• In case of faults or poor operation of the unit,deactivate it; do not attempt to repair or directly operate on it. Only contact 

professionally qualified personnel.

• After removing the packing, check the integrity of the contents.

• The packing materials are a potential source of hazard and must be kept out of thereach of children.

 WARNINGS

Summary of Contents for ECO 5.5 P



















Reviews: