- 16
-
In caso di blocco bruciatore nel pulsante di blocco sarà fissa la luce rossa.
Premendo il pulsante trasparente si procede allo sblocco del dispositivo di comando e controllo.
Premendo per più di 3 sec. la fase di diagnosi verrà attivata (luce rossa con lampeggio rapido), nella tabella sottostante
viene riportato il significato della causa di blocco o malfunzionamento in funzione del numero di lampeggi (sempre di
colore rosso). Premendo il pulsante di sblocco per almeno 3 sec. si interromperà la funzione di diagnosi.
DIAGNOSI DELLE CAUSE DI MALFUNZIONAMENTO E BLOCCO APP. LME
Ri epilogo anomalie di funzionamento
Indicazione ottica
Possibile cause
2 lampeggi
Y
Y
Assenza del segnale di fiamma
-
M
-
Malfunzionamento pressostato aria
-
Perdita segnale pressostato aria dopo T10
-
Contatto pressostato aria aperto
alfunzionamento valvole combustibile
-
Malfunzionamento rilevatore fiam ma
-
Difettosità nella taratura del bruciatore , assenza di
combustibile
-
Ma ncata accensione
3 lampeggi
Y
Y
Y
4 lampeggi
Y
Y
Y
Y
Luce estranea all’ accensione
5 lampeggi
Y
Y
Y
Y
Y
Libero
6 lampeggi
Y
Y
Y
Y
Y
Y
Libero
7 lampeggi
Y
Y
Y
Y
Y
Y
Y
Assenza del segnale di fiamma durant e f unzionamento
-
Malfunzionamento valvole combustibile
-
Malfunzionamento rilevatore fiam ma
-
Difettosità nella taratura del bruciatore , assenza di
combustibile
8 lampeggi
Y
Y
Y
Y
Y
Y
Y
Y
9 lampeggi
Y
Y
Y
Y
Y
Y
Y
Y
Y
Libero
Libero
10 lampeggi
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Errori di collegamento elettrico o danni all’apparecchiatura
14 lampeggi
Y
Y
Y
Y
Y Y Y Y
Y
Y
Y
Y
Y
Y
Linea termostati aperta
ALLACCIAMENTO GAS
L’impianto deve essere completo degli accessori prescritti dalle normative. La buona tecnica consiglia di prevedere sem-
pre un filtro, di non esercitare sforzi meccanici sui componenti e perciò prevedere un giunto elastico, uno stabilizzatore
di pressione ed un rubinetto di intercettazione all’ingresso della centrale termica. La posa in opera della tubazione deve
essere fatta con tubo rigido. Eventuali tubi flessibili devono essere di tipo omologato.
Si tenga inoltre presente la necessità degli spazi richiesti per la manutenzione del bruciatore e della caldaia. Dopo aver
montato il gruppo valvole sul bruciatore, verificare l’assenza di fughe di gas durante la fase di prima accensione.
Summary of Contents for EM 40/2-E
