- 84
-
EINSTELLUNG VENTIL MULTIBLOC
1 Sicherungsschraube Einstellung Durchsatz 1./2. Flamme
2 Einstellung
Stabilisator
3 Schutzdeckel
Einstellung
Anfangs-Schnellauslösung
4 Einstellung Durchsatz 2. Flamme
5 Einstellung Durchsatz 1. Flamme
Zum Einstellen des Durchsatzes der 1./2. Flamme die Schraube 1 lösen.
Durch Drehen von 4 und 5 gegen den Uhrzeigersinn wird der Durchsatz
erhöht, durch Drehen im Uhrzeigersinn wird er verringert. Die Einstellungen
vornehmen, dann die Schraube 1 wieder anziehen. Die Einstellung der
Anfangs-Schnellauslösung erfolgt nach Abnahme des Deckels 3 und unter
Verwendung seines hinteren Teils als Werkzeug zum Drehen des Stifts.
EINSTELLUNG GASVENTIL
Es müssen der Höchstdurchsatz und der Anfangsdurchsatz eingestellt werden.
EINSTELLUNG HÖCHSTDURCHSATZ
- Ein Manometer zum Messen des Gasdrucks am Brennerkopf anbringen;
- das Gasventil vollständig öffnen;
- bei laufendem Brenner den Stabilisator einstellen, bis der gewün-
schte Durchsatz erreicht ist (Ablesung am Zähler); den Druckwert am
Manometer ablesen;
- das Ventil in Rictung Schließung betätigen, bis der Druck am Manometer
nachzulassen beginnt. Jetzt ist der gewünschte Höchstdurchsatz festge-
legt und wird sowohl vom Stabilisator als auch vom Gasventil kontrolliert.
ÜBERPRÜFUNG DER GASMENGE BEIM START
Die Überprüfung der Gasmenge beim Start erfolgt durch Anwendung der
folgenden Formel:
Ts x Qs
100
wobei
Ts
= Sicherheitsspanne in Sekunden.
Qs
= in der Sicherheitsspanne freigesetze Energie, ausgedrückt in kW.
Den Wert Qs erhält man aus:
wobei
Q1
= bei 10 Startversuchen in der Sicherheitsspanne freigesetzter Durchsatz, ausgedrückt in Litern
Ts1
= Summe der effektiven Sicherheitsspanne bei 10 Startversuchen
Qn
=
Nennleistung
Um
Q1
zu erhalten, muß folgendermaßen vorgegangen werden:
- Das Kabel der Überwachungselektrode abnehmen (Ionisierungselektrode).
- Vor dem Test den Gaszähler ablesen.
- 10 Zündversuche des Brenners vornehmen, was 10 Sicherheitssperren entspricht. Erneut den Gaszähler ablesen; man
erhält den Wert
Q1
, wenn man davon den Wert der Anfangsablesung abzieht.
Beispiel:
Anfangsablesung
00006,682 Liter
Endablesung
00006,947 Liter
Gesamtwert
Q1
00000,265
Liter
Manometer
Summary of Contents for EM 40/2-E
