background image

26

DESCRIPTION

These boilers are fully automatic and gas control is effected by an electronic control unit having the
following characteristics:

-

continuous modulation mode on both circuits;

-

possibility to adjust the heating output;

-

possibility to adjust the slow ignition;

-

“anti-Legionnaire’s” function

They are equipped with:

-

Safety flow-switch;

-

Total safety thermostat;

-

High efficiency flue gas exchanger;

-

60-liter tank in stainless steel for plenty of hot water

-

Electric 3-way valve

VELA X N 24 MB W TOP

Electronic ignition with ionisation flame control.
Combustion and fume discharge are of the atmospheric type. Fitted with FLUE CONTROL fume evacu-
ation device.

FLUE CONTROL THERMOSTAT

VELA X N MB boilers are fitted with the FLUE CONTROL device to control evacuation of fumes. An
increase in fume temperature in the down-draught diverter indicates an anomaly in fume evacuation.
The FLUE CONTROL probe in the down-draught diverter detects variations in temperature and shuts
down the boiler. Efficient operation of this safety system depends on observance of the following:
-

Do not deactivate the FLUE CONTROL thermostat.

-

Inspect the boiler and the flue immediately if the FLUE CONTROL device trips frequently.

-

If the FLUE CONTROL device is changed make sure you observe assembly and probe positioning
instructions carefully and use only 

original LAMBORGHINI

 spare parts.

If there is a fume evacuation anomaly act quickly to prevent the formation of Carbon Monoxide, a
poisonous gas that causes intoxication and potentially fatal harm to both humans and animals.

Summary of Contents for Vela XN 24 MB/IT































Reviews: