background image

11

(15190) PreLOG   

          Operating Instructions 

Operating Instructions
Data Logger PreLOG (15190)

8.1 Recording

Recording of Precipitation Pulses With Timestamp

The PreLOG records each pulse with the value of the resolution factor and a timestamp. Thus times without 
precipitation will not be explicitly registered. With activated precipitation correction the corrected values will be 
recorded.

Attention! Since the real time clock has a resolution of 1 s, it is possible that at very high inten-

sities multiple values (pulses) will be recorded with the same timestamp! 

With resolution factors < 0.1 it is recommended to record the precipitation in sums of con

fi

 gurable time intervals 

instead of individual pulses.

Example:

Recording individual pulses; correction activated

Date

Time

Precipitation (in mm/m²)

01/11/2013

12:12:01

0.1

01/11/2013

12:13:01

0.1

01/11/2013

12:13:03

0.132 (corrected)

01/11/2013

12:13:06

0.112 (corrected)

...

...

...

Confi guration

The recording of individual pulses will be activated, if the option “

Individual Pulses

” is selected in the selection 

box “

Setup – PreLOG Con

fi

 guration – Operating Mode – Time Base

” in the PreLOG-Commander. In the same 

area you have to select the corresponding resolution factor of the sensor.

The date and time of the real time clock of the PreLOG is set by the function “

Setup – Set PreLOG Clock

” of the 

PreLOG-Commander. By default the function suggests the date and time of the PC clock.

The circular buffer of the PreLOG can store up to 65535 measured values. Therefore the recorded values have 
to be retrieved in appropriate time intervals. If the memory is full, the oldest value will be overwritten.

Recording of Precipitation Amounts in a Selectable Period

As an alternative the PreLOG can add up the received pulses of a selectable period with their (corrected) resolu-
tion factor and record the resulting “precipitation sums”. Hence the PreLOG can record the precipitation amount 
e. g. at 1 min intervals.
With activated precipitation correction the corrected values will be recorded. Recording will take place on the  
minute mark. Only values > 0 mm/m² will be recorded.

Example:

Recording every 10 min; correction activated

Date

Time

Precipitation (in mm/m²)

01/11/2013

12:10:00

0.5

01/11/2013

12:20:00

2.611 (corrected)

01/11/2013

14:10:00

0.8

01/12/2013

06:50:00

0.2

...

...

...

Con

fi

 guration

The recording of the precipitation amount in periods of time will be activated in the PreLOG-Commander in the 
selection box “

Setup – PreLOG Con

fi

 guration – Operating Mode – Time Base

” by selecting a time in min.

The corresponding resolution factor has to be speci

fi

 ed in the same area. 

It is recommended to record in 1 or 10 min intervals. If the processing should be done with the software MeteoWare 

Summary of Contents for 15190































Reviews: