background image

Section 1: Key Information

Key Points About Laminex

®

 Metaline Splashbacks and  

Panel Systems

1.1  Important Information

1.   Laminex Metaline splashback and panel systems 

must

 be installed as per 

Section 5 - “Kitchen Splashbacks Installations” contained in this manual to 
deliver optimum product performance and compliance with the warranty. 

2.   The minimum set back distance between the installed Laminex Metaline 

splashback panel and any cook top (gas or electric) is 30mm. This is to ensure 
compliance with the building codes, as well as to prevent impact and thermal 
damage caused by oversized pots being used on the rear burner or element. 
Installations that are closer than 30mm will not be warranted. Laminex Metaline 
splashbacks and panels are not suitable for installations behind gas or electric 
cooktops where the benchtop is less than 600mm.

3.   The Laminex Metaline splashback and panel systems has a proprietary coating that 

allows it to be cleaned easily. Cleaning of Metaline splashbacks and panels should 
follow the “Care and Maintenance” section, which is contained later in this manual  
 and also on the consumer warranty card. Deep gouges caused by abrasive cleaners 
or scouring pads will not be warranted.

4.   Laminex Metaline splashbacks have been assessed for fire safety properties. 

Laminex Metaline splashbacks are classified as Group 2 (under specification 
A2.4 of the BCA) and have the typical fire indices of 0 (Ignitability index), 0 
(Spread of flame index), 0 (Heat evolved index) and 1(Smoke developed index).

5.   ALWAYS follow the installation instructions as described in Section 5 of this 

document. Failure to follow the installation instructions may create a potential 
fire hazard to the consumer and will void any warranty. 

6.   All installations must be installed from the same batch and the same sheet 

orientation (information on spotstick) to avoid any colour variation.

1.2  General Information

7.   Safety – always wear appropriate PPE when handling or cutting Laminex 

Metaline splashback panels.  

Summary of Contents for Metaline

























Reviews: