background image

6

IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE
SWITCHED YOUR COOKER HOOD OFF AT THE MAINS SWITCH.

‡

Clean the external parts of your cooker hood with mild liquid detergent and a
damp cloth.

‡

Never use abrasive powder, corrosive solvents or brushes.

‡

Never insert pointed objects into the motor’s protective grid.

‡

If you are using the appliance in recirculation mode, then be sure to replace
the carbon filter at the recommended interval (see section on “Fitting the
carbon filter”). A build up of grease could cause a fire hazard.

‡

IMPORTANT: You should regularly use a good quality stainless steel
cleaner to maintain the shine and finish on the stainless steel areas
of your cooker hood, this will help to leave a silicone water-resistant
film to protect the stainless steel surfaces and keep them in good
condition for the life of the product.

The grease filters

‡

Your cooker hood includes grease filters which help to absorb grease
particles to protect your kitchen & furniture from greasy residues.

‡

These metallic filters may become inflammable if they become saturated
with this greasy residue.

‡

To prevent this fire hazard, the filters should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at least once a
month, using hot water and normal washing-up detergent.

‡

DO NOT WASH THE GREASE FILTERS IN A DISHWASHER.

‡

 Care and Cleaning

Summary of Contents for HJA2182

















Reviews: