EN
a) INSTRUCTIONS FOR USE
Mounting instructions
The main unit is a wall type unit, which guarantees complete electrical safety.
Note:
if you have doubts regarding the correct positioning or mounting of the device, always consult a qualified
electrician.
Positioning of the main unit
We recommend the unit be mounted to the wall, in upright position, at least one metre from the tub and at a height of
1.8-meters in comparison with the floor. The main unit must be positioned in an inaccessible place for any person in the
tub.
It
MUST
be permanently mounted to the wall.
IMPORTANT
Main unit must under no circumstances be mounted to a place from which it could fall in the bath, the sink or the toilet.
We recommend that you connect this unit to a power outlet located outside the bathroom
b) INSTALLATION
1. Main unit should be suspended with the air pipe outlet located downwards.
2. After marking two hole positions, drill 2 holes 5 mm in diameter and 28 mm deep, making sure not to drill the
electrical cables and the water or gas pipes which are built in the wall.
3. Press the wall screws (provided) completely in the holes and screw on the 2 screws provided, by leaving the heads out
about 7 mm.
4. Position the main unit so that the screw heads enter the circular orifice of the holes in the form of «key holes» at the
back of the device.
5. Pull the main unit downwards to position it firmly on the mounting screws.
Note:
It may be necessary to adjust the depth of the screws so that the placement is secure and stable enough. For
hollow partitions with half-timbering, special mounting systems may be necessary (these are not provided however).
3. BATH MAT USE INSTRUCTIONS
1. Place the mat in the empty tub and press on the mat to stick the vacuum cups.
2. Insert the «valve» located at the end of the pipe in the main unit and make it swivel to lock it in place. To do this, pivot
the end of the pipe so that the arrow is placed opposite the closed lock.
3. Insert the other end of the pipe in the mat’s connector cable.
4. With dry hands, plug the power lead in to a power outlet located outside the bathroom and connect the power supply.
5. Choose the desired length of operation with the time switch button. The maximum pre-adjusted length of the time
switch is 60 minutes, but the recommended length is 20 minutes.
6. Also select the program type with the program adjustment button.
7. Then choose the intensity of the bubbles by operating the variable intensity button.
After regulating the main unit, get in the tub to use your hydro-massage.
4. ACCESSOIRES
MASSAGING BRUSH CHARACTERISTICS
• Waterproof, light, portable and compact.
Hydro Care
5
Summary of Contents for Hydro Care
