PAGE 4
SET TIME OF DAY
STEP 1:
Press and Hold
SET HOUR
for 3
seconds.
STEP 2:
Current Time (hour): Set the hour of
the day using ▲ or ▼buttons. AM/ PM toggles
after 12. Pres
SET HOUR
to go to step 3.
STEP 3:
Adjust minutes with ▲ or ▼. Press
SET HOUR
to exit Set Time of Day.
POWER LOSS: Only the current time of day
will need to be reset if power is lost for greater
than 8 hours. If power is lost while the system
is regenerating, the control will complete
regeneration at the point of interruption once
power is restored.
ERROR MESSAGE: if “E1“, “E2”, “E3” or
“E4” appears on the display contact the OEM
for help. This indicates that the valve did not
function properly.
INSTALLATION CONT.
WS1TC & WS1.25 TC Manual
Page 11
Power Loss
Only the current time of day will need to be reset if power is lost for greater than 8 hours. If power is lost while the system is
regenerating, the control will complete regeneration at the point of interuption once power is restored.
Error Message
If “E1,” “E2”, “E3” or “E4” appears on the display contact the OEM for help. This indicates that the
valve did not function properly.
STEP 1U
STEP 2U
Set Time of Day
STEP 1U
– Press SET
STEP 2U
– Current time: Adjust hour with
or
. With 60 Hz line frequency detection on
power-up, timekeeping is 12 hour with PM indicator. With 50 Hz line frequency detection on
power-up, timekeeping is 24 hour without the PM indicator. Press SET to go to Step 3U.
STEP 3U
– Adjust minutes with
or
. Press SET to exit Set Time of Day.
STEP 3U
SET
HOUR
SET
HOUR
SET
HOUR
• Replace the control valve making sure that the distributor tube is inserted into the center hole of the bottom of the
control valve.
• Complete plumbing.
• Place the bypass valve in “BYPASS OPERATION”. (Figure 1)
• Plug the transformer into a 120V uninterrupted receptacle.
• Carbon should be soaked in water for at least one hour before backwashing at full-flow. The mineral is dry
and filling too quickly will result in the mineral plugging the drain line and valve assembly.
16"
MIN.
Distributor
Assembly
Mineral
Tank
Gravel
Support
Bed
Tube
Plug
or
Tape
Keep centered
on bottom
of tank
FIG. A
FIG. B
Tube
When
Adding
Minerals
Valve
FIG. C
5/8" Polytube
Drain Line
Drain
Pipe
Example of an
air-gap set-up
G-175 Air Gap
1-1/2" Solvent x 3/4" FPT
13308 1/2" MPTx5/8"
439-101 3/4" to 1/2"
Worm Gear Type
Hose Clamp
Barbed Fitting,
(not provided)
Reducer Coupling
DRAIN LINE:
The 3/4” drain line elbow accommodates 5/8” poly tube or 3/4” NPT drain line connections. The nut and
poly tube insert for the 3/4” drain line elbow is designed for use with flexible, semi-rigid poly tube only. The drain line elbow
can be rotated so the outlet can be oriented toward the nearest drain.
TO INSTALL 5/8” POLY TUBE DRAIN LINE:
The poly tube insert is shipped attached to the drain line elbow’s locking
clip. Press the insert into the drain line (5/8” poly tube not included). Loosen nut of the drain line elbow. Press 5/8” poly
tube with insert into the drain line elbow until it seats on the back of the fitting. Tighten nut.
The drain line must be piped to an open drain with air gap between the drain and the sewer lines (Fig. C). Under no
circumstances should there be a direct connection with sanitary sewage facilities. If it is necessary to run the drain pipe
overhead, (not to exceed 5’ above valve) be sure to increase the pipe size and follow all plumbing procedures to hold
friction and restrictions to a minimum.
