Lancaster 7-LX-100 Installation, Operating And Service Manual Download | Manualshive

Page: 2 / 30

background image

PAGE 2

MODEL NO.

JOB SPECIFICATIONS

WATER TEST AT TIME OF INSTALLATION

Hardness CaCo

3

(gpg)

Iron (ppm)
pH

Other:

SIZING INFORMATION

All Water is Softened Except:

Rear Hose Bib

Front Hose Bib

Kitchen Cold

Toilets

All Cold

Other

The average family uses 50 gallons per person daily for all water uses in the home.

Daily Water Usage (Gallons/Person)

x

Family Size (Number of people in family)

=

Total Gallons Per Day

x

Grains Per Gallon of hardness

(Note: Add 4 grains per gallon of hardness for each ppm iron for total compensated hardness)

=

Total Grains per Day

INSTALLATION DATE
SERIAL NUMBER
INSTALLER NAME

PHONE

ADDRESS

TABLE OF CONTENTS

Job Specifications

......................................................................................................................... 2

Pre-Installation Review  .................................................................................................................  3
General Installation and Service Warnings  ..................................................................................  3
Bypass Valve Operation  ...............................................................................................................  4
Installation Instructions, Diagrams ................................................................................................  5, 6
Placing Softener into Service  .......................................................................................................  7
General Operation  ........................................................................................................................  7
Set Time of Day  ............................................................................................................................  8
Adjust Hardness, Days Between Regenerations or Time of Regeneration  ..................................  8, 9
Low Battery....................................................................................................................................  9
Contact Screen Programming  ......................................................................................................  9

Specifications

............................................................................................................................... 10-13

Parts Diagrams  .............................................................................................................................  14-21
Service Instructions  ......................................................................................................................  22-24
Troubleshooting  ............................................................................................................................  25-28

«
1
2
3
4
...
»

Summary of Contents for 7-LX-100































Reviews:

No comments

Related manuals for 7-LX-100

ElectriFLEX LD LE Series

Brand: Bradford White Pages: 40

Brand: Daikin Pages: 16

Brand: Wellsys Pages: 23

Brand: Purell Pages: 2

PAW-TD20C1E5-UK

Brand: eco3energy Pages: 16

Brand: JNF Pages: 8

Brand: Campomatic Pages: 18

Brand: Campomatic Pages: 18

Brand: BOWMAN Pages: 3

Brand: State Water Heaters Pages: 24

Brand: Danby Pages: 15

Brand: Genie H2O Pages: 12

Brand: OSO HOTWATER Pages: 80

Brand: Maytag Pages: 36

Brand: Borg & Overstrom Pages: 32

CareSoft Series

Brand: Water Care Pages: 28

Brand: Bunn Pages: 7

Commercial Gas Water Heater

Brand: State Water Heaters Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands