Lancaster 7-LX-100 Installation, Operating And Service Manual Download

Page: 27 / 30

PAGE 27

Problem

Possible Cause

Solution

14. Error – 101 = Control unable to sense motor

movement

a. Motor not inserted full to engage pinion,

motor wires broken or disconnected

a. Disconnect power, make sure motor is

fully engaged, check for broken wires,

make sure two pin connector on motor

is connected to the two pin connection

on the PC Board labeled MOTOR.

Press

NEXT

and

REGEN

buttons for

3 seconds to resynchronize software

with piston position or disconnect

power supply from PC Board for 5

seconds and then reconnect.

b. PC Board not properly snapped into drive

bracket

b. Properly snap PC Board into drive

bracket and then Press

NEXT

and

REGEN

buttons for 3 seconds to

resynchronize software with piston

position or disconnect power supply

from PC Board for 5 seconds and then

reconnect.

c. Missing reduction gears

c. Replace missing gears

15. Error – 102 = Control valve motor ran too

short and was unable to find the next cycle

position and stalled

a. Foreign material is lodged in control valve a. Open up control valve and pull out

piston assembly and seal/ stack

assembly for inspection. Press

NEXT

and

REGEN

buttons for 3 seconds

to resynchronize software with piston

position or disconnect power supply

from PC Board for 5 seconds and then

reconnect.

b. Mechanical binding

b. Check piston and seal/ stack assembly,

check reduction gears, check drive

bracket and main drive gear interface.

Press

NEXT

and

REGEN

buttons for

3 seconds to resynchronize software

with piston position or disconnect

power supply from PC Board for 5

seconds and then reconnect.

c. Main drive gear too tight

c. Loosen main drive gear. Press

NEXT

and

REGEN

buttons for 3 seconds

to resynchronize software with piston

position or disconnect power supply

from PC Board for 5 seconds and then

reconnect.

d. Improper voltage being delivered to PC

Board

d. Verify that proper voltage is being

supplied. Press

NEXT

and

REGEN

buttons for 3 seconds to resynchronize

software with piston position or

disconnect power supply from

PC Board for 5 seconds and then

reconnect.

16. Error – 103 = Control valve motor ran too

long and was unable to find the next cycle

position

a. Motor failure during a regeneration

a. Check motor connections then Press

NEXT

and

REGEN

buttons for 3

seconds to resynchronize software

with piston position or disconnect

power supply from PC Board for 5

seconds and then reconnect.

b. Foreign matter built up on piston and

stack assemblies creating friction and

drag enough to time out motor

b. Replace piston and stack assemblies.

Press

NEXT

and

REGEN

buttons for

3 seconds to resynchronize software

with piston position or disconnect

power supply from PC Board for 5

seconds and then reconnect.

c. Drive bracket not snapped in properly

and out enough that reduction gears and

drive gear do not interface

c. Snap drive bracket in properly then

Press

NEXT

and

REGEN

buttons for

3 seconds to resynchronize software

with piston position or disconnect

power supply from PC Board for 5

seconds and then reconnect.

Summary of Contents for 7-LX-100































Search results

Summary of Contents for 7-LX-100

Reviews:

Related manuals for 7-LX-100

Brands by name

Popular brands

Lancaster 7-LX-100, Installation, Operating And Service Manual

Search results

Summary of Contents for 7-LX-100

Reviews:

Related manuals for 7-LX-100

Brands by name

Popular brands