background image

Lancer Corp., 6655 Lancer Blvd., San Antonio, Texas 78219 - 800-729-1500 - Technical Support/Warranty: 800-729-1550

custserv@lancercorp.com - lancercorp.com - Manual PN: 28-1005/01 - September 2018

“Lancer” is the registered trademark of Lancer © 2018 by Lancer, all rights reserved.

Spare Parts Kit

08

01

07

02

04

06

03

05

Item Part Number Description

Qty

01

10-1017

LED Light Panel, 30”

1

-

10-1021

LED Light Panel, 22”

1

02

05-3712

Badge, 22”/30”, 6/8 Valve, Carma

5

-

05-4003

Badge, 30”, 10 Valve, Carma

5

03

05-3668

Badge Lens, 22”/30”, 6/8 Valve, Carma

5

-

05-4002

Badge Lens, 30”, 10 Valve, Carma

5

04

82-6000

Kit, Decal, Round, New ACIB, 22”/30” - 6/8 Valve, Carma

1

-

82-6011

Kit, Decal, Round, New ACIB, 30” - 10 Valve, Carma

1

05

05-3713/01

Badge Back Cover, New ACIB, 22”/30”, 6/8 Valve, Carma

5

-

05-4004

Badge Back Cover, New ACIB, 30” 10 Valve, Carma

5

06

02-0693

O-Ring, AS568A-142, 2.568 OD X 0.103 THK, 22”/30” 6/8 Valve, Carma

5

-

02-1000

O-Ring, AS568A-142, 2.568 OD X 0.103 THK, 30” - 10 Valve, Carma

5

07

82-6092

Kit, Badge, Carma, 6/8 Valve

1

-

82-6093

Kit, Badge, Carma, 10 Valve

1

08

82-5287/01

Top Cover Assembly, Manual Ice Fill, 30”, 8/10 Valve, Carma

1

-

82-5289

Top Cover Assembly, Manual Ice Fill, 22”, 6 Valve, Carma

1

Summary of Contents for ACIB 22 Series











Reviews: