Land Pride RB16 Series, Operator'S Manual

Section 2: Accessory Equipment Set-Up 

Table of Contents

9/28/18

RB1660, RB1672, RB1684, RB2672, RB2684, &  RB2696  Rear  Blades  301-375M

11

RB26 Series Hydraulic Angling Kit

Refer to Figure 2-1: 

The Hydraulic Angling Kit can be easily attached to the 
RB16 & RB26 Series Rear Blades to make controlling 
blade angle easier. Order the kit that matches your 
Landscape Rake serial number.

RB26/LR26 Series With S/N

301-524ARB26 HYDRAULIC ANGLE KIT

RB26/LR26 Series With S/N 71126 to 986199-

301-426AB26 HYDRAULIC ANGLE KIT

DANGER

!

To avoid serious injury or death:  
Do not remove hardware securing blade pivot cap without 

supporting underside of blade. The blade will fall if not 

supported.

1.

Support rear blade by lowering unit to the ground. If 
unhooked from a tractor, make sure park stand is 
rotated down and secured. 

2. With blade supported, unscrew cap screw (#10). 

Remove pivot cap (#3) and drive pivot cap (#7). Keep 
cap screw (#10) and pivot cap (#3) for reuse. Store 
drive pivot cap (#7). It will come in handy when 
reversing the blade. Refer to 

“Hydraulic Blade 

Reversing” 

on page 15

3. Attach hydraulic angle plate (#6) to blade pivot 

shaft (#5) with 3/4"-10 x 5 1/2" GR5 bolts (#9), hex 
flange top locknuts (#12), pivot cap (#3), and 
3/4"-10 x 1 1/2" hex flange cap screw (#10). Tighten 
locknuts (#12) and hex flange cap screw (#10) to the 
correct torque.

4. Remove hairpin cotter (#14) and hitch pin (#13). 

Remove locknuts (#11) and bolts (#8). Store removed 
hardware with drive pivot cap (#7).

5. Attach front cylinder mount (#4) with new hex flange 

top locknuts (#11) and 1/2"-13 x 3 1/2" GR5 cap 
screws (#8). Tighten locknuts to the correct torque.

6. Attach adapter fittings (#16) to one end of hydraulic 

hoses (#19 & #20) and tighten. 

7.

Attach quick disconnect couplings (#18) to adapter 
fittings (#17) and tighten. (Customer to supply quick 
disconnect hydraulic couplings.)

8. Position hydraulic cylinder (#15) with ports on top 

and cylinder base to the front as shown. Screw 90

o

elbows (#16) into the cylinder ports and tighten 
facing forward as shown.

9. Attach short hydraulic hose (#19) to elbow (#16) at 

the cylinder base and tighten. 

10. Attach long hydraulic hose (#20) to elbow (#16) at the 

cylinder rod end and tighten. 

11. Attach base of hydraulic cylinder (#15) to front 

cylinder mount (#4) with clevis pin (#2) and hairpin 
cotters (#1). Make sure hydraulic ports are 
positioned on top and cylinder base is positioned to 
the front as shown.

12. Attach rod end of hydraulic cylinder (#15) to hydraulic 

angle plate (#6) with clevis pin (#2) and hairpin 
cotters (#1).

IMPORTANT: 

Attach cylinder base to the front 

cylinder mount. The base will interfere with the 
mainframe if attached to rear cylinder mount.

RB26 Series Hydraulic Blade Angling Accessory

Figure 2-2

35499

Customer to supply Quick 
Disconnect Couplings (#18).