Land Pride RCD1884 Operator'S Manual Download

Page: 16 / 44

Section 1: Assembly & Set-up

Table of Contents

7/13/20

RCD1884 Rotary Cutters 326-355M

8. Rotate outer coupler shield closed and replace

existing hand knobs (#14). Hand tighten hand knobs.

Tractor Hook-Up

Refer to Figure 1-3 on page 13:

WARNING

To avoid serious injury or death:
Lightweight tractors with rear attached implements may need

weights added to the front to maintain steering control.

Consult your tractor Operator’s Manual to determine proper

weight requirements and maximum weight limitations.

A 3-Point Category I or II hitch is required. The lower

3-Point arms of the 3-Point hitch must be stabilized to

prevent side-to-side movement. Most tractors have sway

blocks or adjustable chains for this purpose.
1. Locate cutter on a flat level surface.
2. Slowly back tractor up to Rotary Cutter while using

tractor’s 3-Point hydraulic control to align lower

3-Point arm holes with clevis lug holes on the cutter.

3. Engage tractor park brake, shut tractor engine off,

and remove key before dismounting from tractor.

4. Attach lower arms to clevis plates with hitch pins and

secure with linchpins.

5. Connect top center 3-Point link to upper pivot hitch

with clevis pin and hairpin cotter supplied by the

customer.

6. Return to the tractor. Slowly raise and lower

implement carefully to ensure that the drawbar, tires,

and other equipment on the tractor do not contact

cutter frame. Move or remove drawbar if it interferes

with the cutter.

Manually adjust one of the two lower lift arms up or

down to level the Rotary Cutter from left to right.

8. Manually adjust the length of the top-link to level the

Rotary Cutter from front to rear. Final deck leveling

adjustments will be made later.

9. The 3-Point lift cylinders on your tractor should be

adjusted to allow for lateral float. Please consult you

tractor’s manual for adjusting instructions.

Quick Hitch Hook-up

Refer to Figure 1-4 on page 13:

If 3-Point hitch plates won’t stay upright for Quick Hitch

attachment, a hitch pin or bolt (#1) may be inserted into

hole “A” to stabilize hitch plates. Be sure to remove hitch

pin before connecting driveline to the tractor. Hitch pin or

bolt is supplied by customer.

NOTE:

Land Pride’s Quick Hitch can be attached to

the tractor to provide quick and easy 3-point hook-

up and detachment. See your nearest Land Pride

dealer to purchase a Quick-Hitch.

3-Point Hitch Assembly

Refer to Figure 1-2:

1. Attach left-hand hitch plate (#2) to upper mounting

hole in clevis plate with 5/8"-11 x 1 3/4" GR5 cap

screw (#6), two flat washers (#12), and hex nylock

nut (#9). Draw nylock nut up snug, do not tighten.

2. Attach right-hand hitch plate (#3) to upper mounting

hole in clevis plate with 5/8"-11 x 1 3/4" GR5 cap

screw (#6), two flat washers (#12), and hex nylock

nut (#9). Draw nylock nut up snug, do not tighten.

3. Rotate top of hitch plates (#2 & #3) back until bottom

of hitch plates rest against the key stops.

Hitch Assembly

Figure 1-2

4. Attach 2 1/16" long bushing (#1) to left and right-hand

hitch plates (#2 & #3) with 1"-8 x 4" GR5 hex head

cap screw (#7) and hex top locknut (#10).

Tighten top locknut (#10) to torque value listed under

“Additional Torque Values”

on page 37.

5. Attach one end of float chain (#4) between hitch

plates (#2 & #3) with 9/16"-12 x 3 1/2" GR5 cap screw

(#8), two flat washers (#13), and hex top locknut

(#11). Draw locknut (#11) up snug, do not tighten.

6. Remove hand knobs (#14) and rotate flex coupler

shield open.

Attach opposite end of float chain (#4) to deck lugs

with 9/16"-12 x 3 1/2" GR5 cap screw (#8) and top

locknut (#11). Draw locknut up snug, do not tighten.

30998

Large Hole

to the Front

Summary of Contents for RCD1884













































Search results

Summary of Contents for RCD1884

Reviews:

Related manuals for RCD1884

Brands by name

Popular brands

Land Pride RCD1884, Operator'S Manual

Search results

Summary of Contents for RCD1884

Reviews:

Related manuals for RCD1884

Brands by name

Popular brands