Land Pride Rotary Cutter RCR2684 Operator'S Manual Download | Manualshive

Page: 50 / 54

background image

Section 7: Features & Benefits

RCF2784 & RCR2684 S/N Rotary Cutters 326-364M

46

Table of Contents

7/26/19

Section 7:

Features & Benefits

RCF2784 & RCR2684

Features

Benefits

Surpassed rugged industry standards

All Land Pride cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.

5 Year gearbox warranty

A rugged heavy built gearbox capable of handling heavy cutting applications.
Shows Land Pride’s confidence in gearbox integrity.

Gearbox seal protection

Gearbox bottom seal protection for longer bearing life.

130 Horsepower gearbox

A rugged heavy built gearbox capable of handling heavy cutting applications.

Cat. 4 driveline with 4-plate slip-clutch

Excellent gearbox protection with the slip-clutch slipping when encountering
obstruction in blade path. Standard slip-clutch offers convenience over shear-bolts.

Cat. II or III hitch with floating top link

Permits deck to follow the terrain for an even cut.

Quick Hitch Capability

Quick Hitch provides for fast hook-up.

Lower clevis type 3-point hitch

Allows for ease of hook-up to tractor. Also adds additional strength allowing for an
even pull from the tractor’s lower arms, vs. pulling on a single pin design.

84" Cutting width

Wide cutting width, Reduces cutting time in the field.

Heavy 10 gauge deck & 1/4" side skirt
construction

10 gauge deck can withstand more abuse than lighter gauge decks and 1/4" side
skirts provide excellent reinforcement and also protect sides from debris being
thrown against them from the blades.

Box tubing deck supports

Makes for a stronger rigid deck.

Fully welded deck

Robotic welded. Adds additional strength and deck integrity.

Extended cutter front

For increased material flow and added protection.

Round back design

Helps discharge grass better than enclosed or partially enclosed cutters. Also
allows for more efficient handling.

Deck Height
10 1/8" (RCF2784)
9 7/8" (RCR2684)

Allows cutter to handle heavy cutting conditions.

1 1/2" to 12" Cutting height

Provides for a wide range of cutting conditions.

High cutting capacity

Can cut brushy areas with saplings up to 3".

Full length skids with replaceable shoes

Full length skids protect side plate structure, replaceable shoes for convenience.

1/2" x 4" Heat-treated free swinging
blades

Free swinging protects from obstructions. Heat-treated offers longer life.

Splined blade bar

Allows for tight positive fit of stump jumper and blade bar to gearbox output shaft.

Oval stump jumper

Standard stump jumper aids in sliding over obstructions such as stumps, rocks and
debris, which also helps protect gearbox output shaft.

High blade tip speed

Ensures clean cut. (14,369 fpm)

Available with single or dual tailwheel

Dual tailwheels offer greater stability in uneven terrain.

15" Laminated tailwheel

Laminated material is long lasting in rough conditions. Can’t go flat.

1 1/2" Heavy-duty spindle on
tailwheel(s)

Tailwheels take a beating, spindle gives the strength to protect tailwheel assembly.

Optional front guarding

Protect against flying debris.
Customer can choose to include single chain, double chain or rubber guarding.

Optional rear guarding

Protect against flying debris.
Customer can choose to include single chain or double chain.

Standard rear metal band

Protects against flying debris.
Acts as a baffle o help mulch cuttings into smaller pieces.

«
...
48
49
50
51
52
...
»

Summary of Contents for Rotary Cutter RCR2684























































Reviews:

No comments

Related manuals for Rotary Cutter RCR2684

Brand: Rustic Woodworking Pages: 20

Brand: Jacobsen Pages: 24

Brand: Snapper Pages: 32

Brand: QEP Pages: 12

Brand: Dremel Pages: 4

Brand: Mac Afric Pages: 21

PULVERISETTE 19

Brand: Fritsch Pages: 24

Brand: RASOR Pages: 16

Brand: Campbell Hausfeld Pages: 16

Smart Spider DN150/6"

Brand: PICOTE Pages: 26

Brand: Hallde Pages: 55

Brand: Bad Boy Pages: 28

Brand: Vari Pages: 64

GT-2150_SI(6digits)(35)(36)

Brand: Echo Pages: 28

Brand: Cross Tools Pages: 39

Brand: Husqvarna Pages: 12

Brand: Vestax Pages: 16

Brand: Vitrex Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands