background image

28

Section 6: Maintenance & Lubrication

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers   370-027M

2/11/21

Table of Contents

General Maintenance Information

Proper servicing and adjustment is the key to the long life 

of any implement. With careful inspection and routine 

maintenance, you can avoid costly downtime and repair.
Check all bolts after using unit for several hours to be 

sure they are tight. Replace any worn, damaged, or 

illegible safety labels by obtaining new labels from your 

Land Pride dealer.
The parts on your Snow Blower have been specially 

designed and should only be replaced with genuine Land 

Pride parts. Do not alter the Snow Blower in a way which 

will adversely affect its performance.

Tractor Maintenance 

One of the most important things you can do to prevent 

hydraulic system problems is ensure that your tractor's 

reservoir remains free of dirt and contamination. 
Use a clean cloth to wipe hose ends before attaching 

them to your tractor. Replace your tractor’s hydraulic 

filter element at the prescribed intervals. These simple 

maintenances will go a long way to prevent occurrence of 

control valve and hydraulic cylinder problems.

Auger & Impeller Inspection

Refer to Figure 6-1:

1. Check 3/8"-16 GR5 Impeller bolt (#3) for tightness, 

Make certain it is torqued tight.

2. Check impellers (#1) for wear, structural cracks, and 

breakage. Repair or replace impeller before it 

causes structural damage to Snow Blower housing. 

3. Check for bent impellers (#1) that are making contact 

or are about to make contact with Snow Blower 

housing. Repair or replace impeller before it causes 

structural damage to Snow Blower housing.

4. Check auger flighting (#2A) and auger paddles (#2B) 

for wear, structural cracks, bending, and breakage. 

Repair or replace auger before components break-

off and are sent into the impeller or through the air.

5. Check end bearings (#6) for wear. Replace bearings 

that are worn excessively. 

6. Lubricate bearings as required. See lubrication 

schedule for 

“Auger Flange Bearings” 

on page 33.

7. Check bearing mounting bolts (#4) for tightness. 

Make certain they are tightened to the correct torque.

8. Check roller chain and sprocket (#5) for wear and 

chain tightness. Replace chain and/or sprocket if 

they are worn excessively. See 

“Roller Chain Take-

up”

 instructions on page 22.

Section 6: Maintenance & Lubrication

Auger & Impeller Inspection

Figure 6-1

33295

Summary of Contents for SB10 Series











































Reviews: