background image

3

Assembly Instructions

• Carefully align the side frame 

cover. Working from top to bot-
tom, snap the upright side cover 
into place.

• Align the side frame cover 

beneath the end cap and install 
the Phillips head screw.

• Tighten the Phillips head screw 

until side cover aligns with 
endcap.

(Do not over-tighten).

• Check the tension on the drive 

belt by placing the drive belt 
between your thumb and fore-
finger and twisting.

• The proper twist is 45º. If the 

belt needs to be adjusted use a 
7/16” socket and turn the bolt 
underneath the motor pan 
attached to the motor’s hook 
screw.

HOME :

• Route the wire harness 

under-

neath

the elevation motor and 

secure with harness restraint clip
provided. Plug connector into 
circuit board until it snaps 
into place.

COMMERCIAL :

• Route the wire harness 

behind

the elevation motor and secure 
with harness restraint clip pro-
vided. Plug connector into 
circuit board until it snaps 
into place.

The treadbelt is tracked and 
tensioned via the take-up screws 
located at the back of the treadmill.

• Check the tension of the tread-

belt. At proper tension you 
should be able to place your 
hand between the belt and deck 
and reach the center of the 
treadmill. If you cannot reach 
the center, the belt is too tight 
and must be loosened. If your 
hand reaches past the center the 
belt is too loose and must be 
tightened.

• Remove the black motor cover 

screws in the side of the frame.
Place motor cover onto treadmill.

• Attach motor cover with Phillips

head screws provided. Place 
rubber spacer between cover and
frame.

• Plug treadmill into a dedicated 

15A outlet. Walk on treadmill at 
approximately 2.5 mph for 20 to
45 minutes to properly walk 
in lubricant.

STEP 7:

Snap side cover into place

STEP 8:

Install side cover screw.

STEP 9:

Check drive belt tension

STEP 10:

Route the wire harness

STEP 11:

Adjust the treadbelt

STEP 12:

Install motor cover

harness

Summary of Contents for Pro Sports Trainer

























Reviews: