background image

LAN DOLL  COR PO RA TION

TRAILER FIVE YEAR LIM ITED WAR RANTY POL ICY

Lan doll Cor po ra tion war rants each new Trailer struc ture manu fac tured by Lan doll Cor po ra tion to be free from de fects in ma te ri als and

work man ship.   This lim ited war ranty is sub ject to spe cific ex clu sions and does not ap ply to any trailer which has been: 1) sub jected to 

or op er ated with loads which, at any time, have ex ceeded the trail er’s rated ca pac ity or de sign lim its: 2) re paired or al tered out side our 

fac tory in any way so as, in our judg ment, to af fect its sta bil ity or re li abil ity: 3) sub ject to mis use, neg li gence, ac ci dent, or has been op -

er ated in a man ner ex pressly pro hib ited in the in struc tions; or not op er ated in ac cor dance with prac tices ap proved by Lan doll Cor po ra -

tion.  Trailer struc ture shall be con sid ered the frame work of the trailer (main frame and/or rear frame weld ment, goose neck weld ment

and  un der car riage  weld ment)  which  is  fab ri cated  by  Lan doll  Cor po ra tion. 

The sole ob li ga tion of Lan doll Cor po ra tion un der this war ranty shall be lim ited to re pair ing or re plac ing, at its op tion, in ac cor dance with 

the sched ule be low, a de fec tive new Trailer struc ture which shall be iden ti fied to Lan doll Cor po ra tion by way of a Lan doll Cor po ra tion

e- mail War ranty Claim Form within five (5) years from the date of reg is tra tion of Trailer.  War ranty, ex pressed or im plied, will be de nied 

on any Trailer not prop erly reg is tered with the Lan doll Cor po ra tion War ranty De part ment within ten (10) days of the first re tail sale.

Lan doll Cor po ra tion War ranty Staff will iden tify com po nents listed on a War ranty Claim re quired to be re turned for fur ther analy sis.  All

parts re turned to Lan doll Cor po ra tion must be shipped with a Re turn Ma te ri als Authori za tion (RMA) pro vided by the Lan doll Cor po ra -

tion War 

ranty Staff.  De 

fec 

tive com 

po 

nents must re 

turned by the pur 

chaser to Lan 

doll Cor 

po 

ra 

tion with trans 

por 

ta 

tion and freight

charges pre paid within fif teen (15) days af ter re ceipt of the RMA.  The ex ami na tion con ducted by Lan doll Cor po ra tion of re turned parts 

shall dis close to its sat is fac tion the ex tent the com po nent may be de tec tive. 

All la bor and parts war ranty MUST be author ized by Lan doll Cor po ra tion War ranty Staff.  Fail ure to do so will re sult in no war ranty

pay ment of any kind.  La bor will be re im bursed in ac cor dance with pub lished shop rates pre- approved by the Lan doll Cor po ra tion War -

ranty Staff.  Time author ized for spe cific work will be lim ited, where ap pro pri ate, to the hours listed in the Lan doll Cor po ra tion author -

ized Flat Rate Sched ule.

THIS WAR RANTY IS EX PRESSLY IN LIEU OF ALL OTHER WAR RAN TIES OF MA TE RIAL, WORK MAN SHIP, DE SIGN, AP PLI CA -
TION OR OTH ER WISE WITH RE SPECT TO ANY EQUIP MENT, WHETHER EX PRESS OR IMI PLIED, IN CLUD ING WAR RAN TIES
OF MER CHANT ABIL ITY AND FIT NESS FOR A PAR TICU LAR PUR POSE, AND OF ALL OTHER OB LI GA TIONS OR LI ABILI TIES
ON THE PART OF LAN DOLL COPRPO RA TION.

New Trailer Struc ture Sched ule:  Lan doll Cor po ra tion shall bear that por tion of the cost of re pair ing or re plac ing the new struc ture of

the Trailer found to be de fec tive within a sixty (60) month war ranty pe riod pro rated on the fol low ing ba sis:

One (1) Year   - 100%

Three (3) Years - 70%

 Five (5) Years - 50%

Two (2) Years -   80%

Four (4) Years   - 60%

All Bot tom Dump and In dus trial and Util ity Tag Trail ers are ex empt from the 5 year struc tural war ranty and carry a 12 month struc tural

war ranty, due to the rug ged and abu sive off road use in which these off road units typi cally op er ate, and are sub ject to the Com po nent 

Sched ule  be low  .

 

Com po nent  Sched ule:    Com po nents  manu fac tured  by  Lan doll  Cor po ra tion  (other  than  the  Struc ture)  and  Com po nents  sup plied  by

other manu fac tur ers shall be war ranted un der the fol low ing sched ule:

I.

Ax les, Sus pen sions, Land ing Gear, Wheels, Rims, Hubs, Roll ers and Cam Fol low ers,

Hy drau lic  Valve  Body  and  other  Lan doll  Cor po ra tion  Com po nents.

Cov er age:  1 year 100%, Over 1 year 0%

II.

Air Lines, Springs, Air Bags, Lev el ing Valves, Bear ings, Brake Valves, Paint, Oil Seals, En gines,

Brake Drums, Shock Ab sorb ers, Elec tri cal, Cyl in ders, Wear Plates, Hy drau lic Hoses & Con nec tions

Cov er age: 1 - 6 months  100%  Over 6 months 0%

III.  

Tires and Tubes

Cov er age:  War ranty claims must be made di rectly to the tire deal ers.

IV. 

Wood  Com po nents

Cov er age:   0%

This war ranty does not ex pand, en large upon or al ter in any way, the war ran ties pro vided by the origi nal manu fac tur ers and sup pli ers

of com po nent parts and ac ces so ries.  This war ranty ex cludes such parts or ac ces so ries which are not de fec tive, but may wear out and 

have to be re placed dur ing the war ranty pe riod, in clud ing, but not lim ited to, light bulbs, paint, brake lin ing, brake drums, wood pieces

and the like. (Tire War ran ties are ex pressly ex cluded from Lan doll Cor po ra tion war ranty herein.) Pur chaser is ex pected to pay all re -

pairs or re place ment costs, in con nec tion with this Agree ment, in clud ing sales and other taxes im me di ately upon com ple tion of work

per formed.

LIMI TA TION  OF  LI ABIL ITY:  Lan doll  Cor po ra tion  shall  not  be  li able  to  pur chaser  for  any  in ci den tal  or  con se quen tial  dam ages  suf fered

by the pur chaser, in clud ing, but not lim ited to, any com mer cially rea son able charges, ex penses or com mis sions in curred in con nec tion

with ef fect ing cover or any other rea son able ex pense in ci dent to the de lay or other breach of war ranty by Lan doll Cor po ra tion, any loss 

of or dam age to any cargo loaded or shipped in or on the Trailer, loss of an tici pated prof its, trans por ta tion ex penses due to re pairs,

non- operation or in creased ex pense of op era tion costs of pur chased or re placed equip ment, claim of cus tom ers, cost of money, any

loss of use of capi tal or reve nue, equip ment rental, road side as sis tance, or for any spe cial dam age or loss of any na ture aris ing at any 

time or from any cause what so ever.

LIMI TA TION OF REM EDY: In the event of Lan doll Cor po ra tion fail ure to re pair the Trailer sub ject to the war ranty con tained herein, the 

pur chas er’s sole and ex clu sive rem edy against Lan doll Cor po ra tion shall be for the re pair or re place ment of any de fec tive part or parts 

of the Trailer sub ject to work or re pair within the time pe riod and man ner set forth herein. This ex clu sive rem edy shall not be deemed

to have failed of its es sen tial pur pose so long as Lan doll Cor po ra tion is will ing and able to re pair or re place de fec tive parts in the pre -

scribed man ner.

Summary of Contents for 318C













































































Reviews: