Landoll BRILLION SL Series, Operator'S Manual

OPERATION

3-7

Electronic Acre Meter Kit - 

Optional

IMPORTANT

Acre Meter is dust and splash resistant, under no 
circumstances should this unit be submerged in any 
conductive, corrosive, or flammable liquid. At no 
time use high pressure water or air to clean it, as this 
can damage the unit.

Settings for Loup Acre Meters

The battery operated Acre Meter operates in one of two 
modes. 
1. In sleep mode, the display is blank, and the counter 

is accumulating acres. Sleep mode will be entered if 
a button is not pressed for 20 seconds. 

2. In entry mode, the display is on, and the operator can 

enter values. To get into entry mode, press the  

*

/FUNC

 button. If you continue to press the  

*

/FUNC

button, the acre counter will cycle through the 
functions that it can perform. The LEDs above the 
display indicate which function is selected.

The available functions are

:

Field Acres, Total Acres, Pulses per 400 feet, Width, 
Password and Low Battery

Field Acres

Press the   

*

/FUNC

 button until the “

FIELD

” LED is lit. 

The digits indicate the acres covered since the field acre 
counter was cleared.
To clear the field acre count, press the 

UP

 and 

DOWN

buttons simultaneously for two seconds. If a password 
has been entered, you will not be able to clear the total 
acre count. Field acres will count in tenths of an acre up 
to 9999.9 acres.

Total Acres

Press the  

*

/FUNC 

button until the “

FIELD

” and “

TOTAL

” 

LEDs are lit. The digits indicate the acres covered since 
the total acre counter was cleared.
To clear the total acre count, press and hold the 

UP

 and

DOWN

 buttons for two seconds. If a password has been

entered, you will not be able to clear the total acre count.
Total acres will count from.1 to 99999 acres.

Pulses Per 400 Feet

Press the  

*

/FUNC

 button until the “

PULSES

” LED is lit. 

The number in the display indicates how many pulses are 
generated for every 400 feet driven. There are two 
methods to enter the pulses per 400 feet:

1. If you know the number, select it using the 

UP

 and 

DOWN

 buttons. When you press the   

*

/FUNC

button, the Acre Counter will accept the number in 
the display as the new pulses per 400 feet. 

See 

Table 3-1

.

2. If you do not know the pulses per 400 feet, press and 

hold the 

UP

 and 

DOWN

 buttons until the “0” appears 

in the display. The “

PULSES

” LED will blink. The 

acre counter is now counting shaft rotations. Enter 
the cab and drive 400 feet. Press the  

*

/FUNC

 button 

to wake up the acre counter. The “

PULSES

” LED will 

light. The number displayed is the pulses per 400 
feet. Press the 

*

/FUNC 

button to accept the setting.

If a password is set, you will not be able to adjust the 
pulses.

Width

Press the 

*

/FUNC button until the “WIDTH” LED is lit. 

The number displayed is the length of your implement in 
feet.
To adjust the width, press the 

UP

 and 

DOWN

 buttons. If 

a password has been entered, you will not be able to 
adjust the width.
The width can be adjusted from .1 to 99.9 feet, in tenths 
of a foot.

Password

The password function allows you to protect the total 
acre count, pulses per 400 feet, and width settings with a 
password. This stops anyone from accidentally changing 
those settings. When the acre counter is shipped, the 
password is disabled. You can modify the pulses per 400 
feet and implement width at any time.
Press the 

*

/FUNC

 button until the “

PASS

” LED is lit. The 

digits will display the word “

Ent

” or “

dIS

”.

If the display shows “dIS”

. The password is disabled. 

The total acre count, pulses/400 feet, width, and 
password settings can be adjusted using the 

UP

 and 

DOWN

 buttons. The password can also be changed 

using the 

UP

 and 

DOWN

 buttons. 

If the display shows “

Ent

”: You must enter your password 

using the 

UP

 and 

DOWN

 buttons. When your password 

is displayed, press the 

*

/FUNC 

button to test the 

password. If the password is correct, you will be able to 
change the acre counter settings. The password will be 
viewable until the acre counter powers down. When the 
acre counter is powered up again, you will have to 
re-enter the password to change settings.
If the password is correct, you will be able to change the 
acre counter settings. The password will be viewable 
until the acre counter powers down. When the acre 
counter is powered up again, you will have to re-enter the 
password to change settings.