2-12
1P124-2306
Warning Lamp Installation,
12FT
NOTE
12FT 3-PT model is shown, Drawbar model similar.
1. Place a Red Lamp at each end of the Light Bar and
insert the Red Lamp Cord into the Light Bar cutout.
Secure Red Lamp to Light Bar with 1/4-20 x 1-1/4
Bolts and Locknuts.
2. Attach Amber Lamps to the outer ends of the Seed
Boxes with 1/4-20 x 1-1/4 Bolts and Locknuts.
3. Attach the Flasher Control Module to the Module
Bracket with 1/4-20 x 1-1/2 Bolts and Locknuts.
IMPORTANT
Cords are marked Yellow Tape for Left and Green
Tape for Right.
4. Lay out the Lamp Harness along the Seeder Frame
Tube, Cords with Yellow Tape Left and Cords with
Green Tape Right. Connect the Harness to the
Flasher Control Module 6-Prong Connector.
5. Route the left and right cords along the front of the
Frame Tube. Route the 3-Prong Connector Cords into
the Light Bar vertical tube openings up to the Red
Lamps and connect. Continue routing the 2-Prong
Connector Cord along the front of the frame, up the
outer Light Bracket to the Amber Lamps and connect.
6. Lay out the 7-Pin Harness along the 3-PT Hitch or
Drawbar with the 4-Prong Connector towards Seeder.
3-PT Hitch, route the 4-Prong Connector Cord
through the Frame Loop to the Module. Drawbar,
route the 7-Pin Harness along the Drawbar, through
the Hose Support up to the Tractor. Connect 7-Pin
Harness 4-Prong Connector to the Flasher Control
Module.
7. Bundle and secure excess cord to the Module Bracket
with Tie Wraps. Along the Frame, secure Harnesses
with Tie Wraps to the slots within the Frame and
Harness Mounting Strips. Secure the Amber Lamp
cords to the ends of the Seed Box with Adhesive
Mounts and Tie Wraps. Bundle and secure 7-Pin
Harness to the Drawbar Hydraulic Hoses or 3-PT
Hitch Frame Slots allowing enough Harness length to
reach the Tractor Socket.
NOTE
Install, route and secure Electric Clutch Harness with the
Lamp Harness.
IMPORTANT
All Harnesses must be firmly attached to Machine
Frame members or Hydraulic Hoses so they do not
sag or become torn loose by field debris.
8. Attach the SMV sign to the SMV Mount located on the
center on the Light Bar with 5/16-18 x 1 Bolts, Flat
Washers, and Locknuts.
9. Attach the Connector Holder to the 3-PT Hitch or
Drawbar Hose Holder with 1/4-20 x 1 Bolts, Flat
Washers, and Locknuts.
NOTE
The 7-Pin Plug on the other end of the 7-Pin Harness
connects to the Tractor Socket when in use. When not in
use, it can be stored in the Connector Holder on the
Drawbar Hose Holder or 3-PT Hitch. Allow enough
Harness length to reach Tractor Socket and roll or fold up
excess and secure to Drawbar Hydraulic Hoses or 3-PT
Hitch.
Figure 2-18: Flasher Control Module and Bracket
Module Bracket
Flasher Control Module
Locknut,1/4-20
Bolt,
1/4-20 x 1-1/2
Summary of Contents for Brillion Turfmaker III Series
