1P124-2306
3-5
Tractor Preparation for
Attaching Pull Type Seeder
DANGER
DANGER
1. Align the Tractor Drawbar with the machine. Raise or
lower the Drawbar, as needed, using the Jack. Attach
the unit with proper size Hitch Pin and Safety Clip.
2. Always move the Jack to the transport position before
setting the machine in motion.
3. Clean all Hydraulic Couplings and attach to the
Tractor.
4. Attach Safety Chain to tractor allowing plenty of
movement for turning both directions. The Safety
Chain should latch securely to prevent it from coming
loose.
IMPORTANT
If the Clevis Pin is not installed, the Transport Lock
may bounce up and cause significant damage to the
Cylinder and Hydraulic Fittings.
Figure 3-5: Safety Chain
5. If Transport Locks are not engaged, fully extend the
Hydraulic Lift Cylinders and rotate Transport Locks in
the engaged position over the Cylinder Rods. Secure
with the Clevis Pins and Hairpin Cotters.
Figure 3-6: Transport Lock Engaged
6. Connect the 7-Pin Connector to Tractor Outlet,
routing cable by avoiding pinch points.
• Make sure the Tractor has a good clean
Receptacle, free of dirt and corrosion.
• Make sure the 7-Pin Connector is inserted ALL
the way in. With tighter fitting pins, operator may
think the Connector is all the way in, but really
isn’t.
• Make sure the Tractor Receptacle Cover latches
over the keyway on the 7-Pin Connector to hold
the Connector in place.
• If an operator plugs in the 7-Pin Connector, but
the lights do not seem to work right, check the
above items to make sure there is a good
connection with the 7-Pin Connector.
7. Install Clutch Switch Box or Brillion Elite Mini Monitor
to tractor.
Clutch Switch Box:
Connect Clutch Switch Box
Cord with Ring Terminals to tractor power source.
Ring Terminals can be removed and replaced with a
different power source connector. Connect 2-Pin
Connector to Clutch Harness.
Brillion Elite Mini Monitor:
Connect the Elite Mini
Tractor Harness to 14-Pin Connector to Brillion Mini
Monitor, 3-Pin Plug to the 12 Volt Tractor
Convenience Outlet and 6-Pin Connector to 240"
Extension Harness. Elite Mini Tractor Harness 4-Pin
Connector is not used this time.
Do not allow any bystanders to stand between the
tractor and the machine while backing up to the
machine.
Drawbar
Support
Locknut, 3/4-10
Bolt,
3/4-10 x 2-1/4
9" Max.
Tractor Drawbar
Safety Chain
Flat
Washer,3/4"
Safety Chain
Intermediate
Support
Wheel Arm
Transport Lock
Clevis Pin
Hair Pin
Cotter
Frame
Engaged
Cylinder
Summary of Contents for Brillion Turfmaker III Series
