1P124-2306
2-15
Electric Clutch Kit - Optional
IMPORTANT
At no time use high pressure water or air to clean the
Electric Clutch as damage could occur.
1. Verify that the Electric Clutch has 1/8" clearance
between the Clutch Housing and Rubber Bumper
Stop. Improper clearance may prevent the Clutch
from engaging or disengaging.
Figure 2-21: Clutch Detail
2. Connect Clutch Harness or Seeder Harness 2-Pin
Connector to Clutch Lead and route along Frame and
Drawbar/3-PT Hitch. Secure to Frame and
Drawbar/3-PT Hitch or to Hydraulic Hoses and Warning
Lamp Harness with tie wraps.
Figure 2-22: Clutch Harness
3. Install Clutch Switch Box or Monitor on Tractor in a
convenient location with Hook and Loop Tape or
Brackets included or another type of mount (not
included).
4.
Clutch Switch Box:
Connect Clutch Harness to
Clutch Switch Box Cord. Connect Clutch Switch Box
Cord with Ring Terminals to tractor power source.
Ring Terminals can be removed
and replaced with a different power source connector.
Brillion Elite Mini Monitor:
Connect the Elite Mini
Tractor Harness 14-Pin Connector to Brillion Elite
Mini Monitor, 3-Pin Power Plug to 12 Volt Tractor
Convenience Outlet and 6-Pin Connector to the 240"
Extension Harness. 4-Pin Connector is not used at
this time. Connect 240" Extension Harness to Seeder
Harness. Secure Harnesses with tie wraps.
5. Check Electric Clutch Operation. The Electric Clutch
will disengage when power is applied. (Clutch will
make a clicking sound). Set Seeder on the ground
and drive a short distance while toggling the Seeder
Clutch to
"ON/SEED"
and
"OFF/NO SEED".
The
Seed Shaft will stop rotating when Monitor or Toggle
Switch is set to
"OFF/NO SEED"
.
6. Set Monitor or Toggle Switch to
"ON/SEED"
position
when Seeder is not used to shut off power to prevent
possible overheating of Clutch Coil.
Electric Clutch Attributes:
•
The Electric Clutch is controlled by a Touch Screen
Monitor or a Toggle Switch Box mounted to the Tractor.
Brillion Elite Mini Monitor:
Touch Screen Monitor
provides the user the ability to turn the Seeder Clutch
"ON"
or
"OFF".
Clutch Switch Box:
Toggle Switch on the Switch
Box, turns the Seeder Clutch to
"SEED"
or
"NO
SEED".
Console w/Clutch Control:
Toggle Switch on the
Console, turns the Seeder Clutch to
"SEED"
or
"NO
SEED".
•
The Electric Clutch is disengaged when power (12
Volts) is applied. If there is a power failure or electrical
problem, the Seeder will continue to operate, so the
machine must be raised to stop seeding.
•
Seed Shafts will not rotate when the machine is
backed up.
•
The Clutch Switch Box contains a 5 Amp Time-Delay
Fuse.
•
The Electric Clutch must be disengaged (power
applied) when Seed Shafts are turned manually for
Calibration
.
Figure 2-23: Switch Box Assembly
1/8" Gap
Bumper Bolt
Rubber Bumper
Stop
Electric
Clutch
Clutch Lead
Electric Clutch
Clutch
Harness
Hydraulic
Hoses
Switch Box
Toggle Switch
Clutch Connector
connect Terminal
to Power Source
Summary of Contents for Brillion Turfmaker III Series
