background image

PARTS LIST AND DIAGRAM

PLEASE READ THE FOLLOWING CAREFULLY

The manufacturer and/or distributor has provided the parts list and assembly diagram in this 

manual as a reference tool only. Neither the manufacturer or distributor makes any representa-

tion or warranty of any kind to the buyer that he or she is qualified to make any repairs to the 

product, or that he or she is qualified to replace any parts of the product. In fact, the manufac-

turer and/or distributor expressly states that all repairs and parts replacements should be 

undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all 

risk and liability arising out of his or her repairs to the original product or replacement parts

Thereto, or arising out of his or her installation of replacement parts thereto.

E8

Part No.

1
2
3
4
5
6
7
8
9

10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34

Description
Hopper
Scraps Defend Block
Clamp Bar
Screw
Hopper Locking Knob
Spring
Up Housing
Frame
Switch Pin
Screw
 Push Stick
“H” Type Screw
Hexagon Screw
Washer
Spring Washer 1
Clamp Block
Screw
Blade
Blade Plate
Drive Block
Shaft Sheath
Blade Defend Block
Screw
Down Housing
25 Nut 1
Nut Frame Plate
Hex Nut
Switch
Spring Washer 2
Switch Frame Plate
Screw
Power Cord
Cord Sheath
Cord Clamp Plate

Q’ty

1
1
1

23

1
1
1
1
1
7
1
2
1
1
1
1
4
2
1
1
1
1

12

1
1
1
4
1
4
1
2
1
1
1

Part No.

35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68

Description
Connecting Wire 2
Connecting Wire 1
Power Switch
Reset Button
Motor Casing
Motor Cover
Capacitor
Fan
Bearing
Screw
Motor Support
Carbon Brush
Brush Box
Field
Armature
Bearing
Wind Defend Board
Down Cover Of Gear Box
Small Belt Wheel
Nut
Bearing
Eccentric Wheel
Big Belt Wheel
Belt
Up Cover Of Gear Box
Bearing
Spanner
Wheel Cover
Pin
Lower Frame
Axle
Washer
Bushing
Wheel

Q’ty

1
1
1
1
1
1
1
1
1
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
4
2
2

Summary of Contents for GUO023













Reviews: