background image

TECHNICAL DETAILS

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey 

all safety messages that follow this symbol to avoid possible injury or death.

DANGER 

Indicates a hazardous situation which, if not avoided, will result in 

death or serious injury.

WARNING

 Indicates a hazardous situation which, if not avoided, could result in 

death or serious injury.

CAUTI0N 

Indicates a hazardous situation which, if not avoided, could result in 

minor or moderate injury.

NOTICE/CAUTION

 Addresses practices not related to personal injury.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

 When using electric gardening appliances, basic safety precautions 

should always be followed to reduce the risk of fire, electric shock, and personal 

injury, including the following:

READ ALL INSTRUCTIONS

Power Cord Safety

WARNING

 To reduce the risk of electric shock, use only with an extension cord

intended for outdoor use, such as an extension cord of cord type SW-A, SOW-A, 

STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.

1. Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or 

outlet(s) to be used for the gardening appliance. Receptacles are available having built-in 

GFCI protection and may be used for this measure of safety.

2. Do not Abuse Cord - Do not carry appliance by cord or yank it to disconnect from receptacle. 

Keep cord from heat, oil, and sharp edges.

3. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider 

than the other) and will require the use of a polarized extension cord. The appliance plug will 

fit into a polarized extension cord only one way. If the plug does not fit fully into the extension 

cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. 

A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into 

the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse 

the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall 

outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug 

in any way. This design is referred to as double-insulated, indicated by

4. WARNING: The cord of this product contains lead, a chemical known to the State of 

California to cause cancer, and birth defects or other reproductive harm. Wash hands after 

handling. (California Health & Safety Code § 25249.5, et seq.)

E1

Electrical Rating
Blade Speed
Blade Diameter
Maximum Limb Capacity

120VAC / 60Hz / 15A
4,300 RPM
7"
1.57" Diameter

Summary of Contents for GUO023













Reviews: