background image

The Dark Art: 

In an age where guitar players have developed an unhealthy fascination with pre-amp distortion, the 

fabled sound of a tube power amp being pushed hard has almost passed into history.  Until now that is!

The L20T-112’s hand wired 20W Class A Single Ended output stage oozes classic, warm tube tones:  The harder you 
drive it, the better it sounds.  Plus with enough gain for contemporary tones, it also has a mean, spiteful side to it as 
well – making it ideal for any style of playing.  Perfect for stage and studio use.

Every Lionheart product is extensively play tested by experienced 
guitarists before being shipped to our customers. Only when the 
unit is finished to our complete satisfaction is it assigned its own 
unique build number which is then hand stamped onto the rear 
mounted plaque.

Your L20T-112 should give you years of trouble-free amplification, 
however please take time to read this manual and familiarise yourself 
with the controls as it will allow you to get the best from your 
amplifier. 

We hope you enjoy using your L20T-112 as much as we enjoyed 
designing and making it. 

Best wishes from all at Laney

INTRODUCTION

L20T

-112

Summary of Contents for L20T-112


















Reviews: