Supply Voltage
~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option
Mains Fuse
~220V>~240V = T2A L. ~100>~120V = T5A L
Power Consumption
300W
Output Power Rating
120W
Loudspeaker
LV300
12” Celestion Custom Designed Driver
LV300Twin
2*12” Celestion Custom Designed Drivers
Features
Rugged construction
ECC83 Tube Drive Stage
Extension speaker socket
(Minimum 8 Ohm Impedance)
FX Loop
(Nominal 750mV Level)
Footswitchable
Yes, Channels and Reverb
(LVFS3 included)
Reverb
Yes
EQ
Both channels contain separate Passive Bass, Middle and Treble
Clean Bright Switch
Independent VScoop switches for Drive 1+2
Input Impedance
1MOhm/47pF
Size
LV300
502*583*286
(H*W*D)
LV300Twin
502*676*286
(
Unit Weight
LV300
17.4 Kg
LV300Twin
19.3 Kg
Packing Weight
LV300
18.2 Kg
LV300Twin
20.5 Kg
VTS - V Tone Shift Technology
H*W*D)
Page 10 /12
Laney
OPERATING INSTRUCTIONS
Page 11 /12
Laney
OPERATING INSTRUCTIONS
General Notes
Amplifier connection:
In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your
equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE
turning on your guitar amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers.
By turning on your guitar amplifier LAST and making sure its Volume controls are set to minimum any transients from other equipment
will not reach your loudspeakers. Wait until all system parts have stabilised; usually a couple of seconds. Similarly when turning off your
system always turn down the Volume controls on your guitar amplifier and then turn off its power before turning off other equipment.
Cables:
never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the
amplifier load and could cause damage to your amplifier system.
Caution:
These professional loudspeaker systems are capable of generating very high sound pressure levels. Use care with placement
and operation to avoid exposure to excessive levels that can cause permanent hearing damage. (Refer to guidelines on page 2)
Servicing:
The user should not attempt to service these products. Refer all servicing to qualified service personnel.
SAMPLE SYSTEM
8 Ohms
Link
Model
RB115
Power Rating
300W Program
Model
RB115
Power Rating
300W Program
Serial Number:
Serial Number:
Input
Laney
Power To The Music
www.laney.co.uk
DESIGNED IN THE UK BY LANEY
8 Ohms
Link
Model
RB115
Power Rating
300W Program
Model
RB115
Power Rating
300W Program
Serial Number:
Serial Number:
Input
Laney
Power To The Music
www.laney.co.uk
DESIGNED IN THE UK BY LANEY
SAMPLE
LV412S
SPECIFICATIONS
This product conforms to the requirements of the following European Regulations, Directives & Rules:-
CE Mark (93/68/EEC), Low Voltage (72/23/EEC), EMC (93/68/EEC),
RoHS (EU2002/95/EC), WEEE (EU2002/96/EC)
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along
with normal
household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE
(Waste Electrical and Electronic Equipment) directive applicable in your country.
Summary of Contents for LV300
Page 1: ...USER MANUAL LV300 LV300Twin...
Page 3: ...Page 3 12...
