background image

TROUBLESHOOTING:

1. Power is off.

1. Make sure power supply is on.

Lights will not turn on.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

2. Faulty switch.

2. Test or replace switch.

3. Faulty wire connection.

3. Check wiring.

Fuse blows or circuit 
breaker trips when light is 
turned on

1. Crossed wires or power wire is 
grounding out.

1. Check wire connections.

• To clean the fixture disconnect power to the fixture by turning off the circuit breaker or by

PRODUCT MAINTENANCE:

turned on.

• To clean the fixture, disconnect power to the fixture by turning off the circuit breaker or by

removing the fuse at the fuse box. Wait a few minutes for the fixture to cool down. Use a
dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the glass
and surface of the fixture.

• Do not use any cleaners with chemicals, solvents or harsh abrasives. If necessary, use a

mild soap to clean off any dirt or stains.

ONE YEAR LIMITED WARRANTY

Langport Lighting

®

warrants this product to be free from defects in material and

gp

g

g

p

workmanship for one year from the original date of purchase by the consumer.

This

warranty is limited to the counter replacement at the time of purchase, with the original
purchase receipt.

Langport Lighting

®

will not be liable for the loss or damage of any

kind, incidental or consequential damages of any kind, whether based on warranty contract
or negligence, and arising in connection with the sale, use or repair of the product claimed
to be defective

Some states do not allow the exclusion or limitation of incidental or

to be defective.

Some states do not allow the exclusion or limitation of incidental or

consequential damages so the above limitation may not apply to you. This warranty gives
you specific legal rights and you may also have other rights, which vary from state to state.
Misuse, accident, improper installation or maintenance will also void the warranty.

Page 11

Summary of Contents for LPT-1006













Reviews: