background image

 

 

FCC Statement 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a 
Class A digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are 
designed to provide reasonable protection against harmful interference when the 
equipment  is  operated  in  a  commercial  environment.  This  equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and 
used  in  accordance  with  the  instruction  manual,  may  cause  harmful 
interference  to  radio  communications.  Operation  of  this  equipment  in  a 
residential area is likely to cause harmful interference in which case the user will 
be required to correct the interference at his own expense. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 

1. 

This device may not cause harmful interference. 

2. 

This device must accept any interference received, including 
interference that may cause undesired operation. 

Any changes or modifications not expressly approved by the party 
responsible  for compliance could void the user’s authority to operate the 
equipment. 

CE Mark Warning 

This is a Class A product. In a domestic environment, this product may cause 
radio interference, in which case the user may be required to take adequate 
measures. 

SAFETY NOTICES 

Caution:

 

Do not use this product near water, for example, in a wet basement or near a 
swimming pool. 

Avoid using this product during an electrical storm. There may be a remote risk of 
electric shock from lightning. 

 

Summary of Contents for LP-SGW2404FP




















Reviews: