3
Breastmilk Expression Set
Item Number
a
Diaphragm Cap
P53410
b
Diaphragm
P53402
c
ComfortFit
®
Breast Cushion (25mm)
P54103
d
Breast Cushion Body
P53454
e
White Valve
P53401
f
160ml (5oz) Bottle
P53451
g
Sealing Cap
P53461
Breast Pump Parts and Accessories
Item Number
h
Silicone Tube (800mm)
P54100
i
Pump Connector
P54106
j
Teat Cover
P53462
k
NaturalWave® Slow Flow Teat
P75900
l
Teat Collar
P53463
m
AC Adapter
P53470
2.2 Cleaning Instructions
Unless otherwise instructed by your health
care provider, follow these instructions.
DO NOT wash tubing or connector.
Before First Use
•
Always wash and dry hands thoroughly with soap and
water before handling the Breastmilk Expression Set.
•
Disassemble the Breastmilk Expression Set and place
parts in a large pot.
•
Cover the parts in water making sure there is room for
all of the parts to float freely in the pot.
•
Bring the water to the boil and allow the parts to a
boil for 5 minutes.
•
After boiling remove the parts from the pot with tongs
and place the pieces neatly on a clean paper towel or
in a clean drying rack and allow them to air dry.
•
Allow the parts to dry completely before assembly and
use. Partially dried parts may affect the operation of
the pump.
•
Once parts are dry they can be stored in a clean plastic
tub with a lid or in a clean plastic zipper bag.
Before Each Pumping Session
•
Always wash and dry hands thoroughly with soap and
water before handling the Breastmilk Expression Set.
•
Before assembling the Breastmilk Expression Set, be
sure that all of the parts are completely dry.
•
Visually inspect the individual components for cracks,
chips, tears, discoloration or deterioration. These may
affect the functionality of the pump.
•
Should you have any questions or concerns about
your parts please visit www.lansinoh.co.uk, call
+44 (0) 113 205 4201
in the UK, or contact your
country distributor for guidance.
Cleaning After Each Pumping Session
•
Disassemble the Breastmilk Expression Set, setting
aside tubing and connector.
•
Rinse all parts with cold water immediately after use.
Place pump parts in a clean wash basin used only for
washing infant feeding equipment. Do not place pump
parts directly in the sink because germs in sinks or
drains could contaminate the pump.
•
Hand wash all parts of the Breastmilk Expression Set
using warm soapy water. A teat brush may be used
to scrub the hard plastic pieces of the Breastmilk
Expression Set, but should not be used on the white
valve or diaphragm.
•
Rinse parts with running clean, warm water, or by
submerging in fresh water in a separate basin that is
only used for cleaning infant feeding equipment.
•
Place parts in a pot and cover with water making sure
there is room for all of the parts to float freely in the pot.
•
Bring the water to a boil and allow to boil for 5 minutes.
•
After boiling remove the parts from the pot with tongs
and place the pieces neatly on a clean paper towel or
in a clean drying rack and allow them to air dry. Do not
use a dish towel to rub or pat items dry because doing
so may transfer germs to the items.
•
Allow the parts to dry completely before assembly and
use. Partially dried parts may affect the operation of
the pump.
•
Once parts are dry they can be stored in a clean plastic
tub with a lid or in a clean plastic zipper bag.
•
Clean your wash basin and bottle and/or teat brush
after each use.
•
The pump unit should be wiped down with a clean paper
towel or soft cloth after use. The pump unit should never be
put into water or other liquids for cleaning.
Parts can be cleaned in a steam or microwave steriliser.
Be sure to follow the manufacturer’s instructions.
f
e
d
c
g
m
b
a
k
l
j
h
i
