10
11
WARNING:
To prevent cross contamination/infection, the Smartpump 2.0 tubing
and breastmilk expression set should never be shared between mothers or re-
sold from one mother to another. Each user should use her own Smartpump 2.0
tubing and breastmilk expression set.
3. CLEANING INSTRUCTIONS
Unless otherwise instructed by your healthcare provider,
follow these sterilising and cleaning instructions.
WARNING:
To prevent cross contamination/infection,
the Smartpump 2.0 tubing and breastmilk expression
set should never be shared between mothers or re-sold
from one mother to another. Each user should use her
own Smartpump 2.0.
3.1 Before First Use
1.
Always wash and dry hands thoroughly with soap and water before handling
the breastmilk expression set.
2.
Disassemble the breastmilk expression set and place parts in a large pot.
3.
Cover the parts in water making sure there is room for all of the parts to float freely
in the pot.
4.
Bring the water to a boil and allow the parts to boil for 5 minutes.
5.
After boiling remove the parts from the pot with tongs and place on a clean
towel to dry, covering the parts with a second towel.
6.
Allow the parts to dry completely before assembly and use. Partially dried
parts may affect the operation of the pump.
7.
Once parts are dry they can be stored in a clean plastic container with a lid or
in a clean plastic sealed bag.
3.2 Cleaning after Each Use
1.
Disassemble the breastmilk expression set, setting aside the tubing and
connectors.
2.
Rinse all parts with cold water immediately after each use. Place pump parts
in a clean washing up bowl used only for washing infant feeding equipment.
Do not place pump parts directly in the sink, because germs in sinks or drains
could contaminate the pump.
3.
Hand wash all parts of the breastmilk expression set using warm soapy water.
A bottle brush may be used to scrub the hard plastic pieces of the breastmilk
expression set, but should not be used on the soft silicone valve or diaphragm.
4.
Rinse parts with running clean, warm water, or by submerging in fresh water
in a separate basin that is used only for cleaning infant feeding items.
5.
Place pump parts on a clean, unused tea towel or paper towel in an area
protected from dirt and dust. Do not use a tea towel to rub or pat items dry.
Allow the parts to dry completely before assembly and use. Partially dried
parts may affect the operation of the pump.
Do not boil or
wash tubing or
connectors!
When sterilising
parts, use enough
water to keep
parts afloat!
6.
Once parts are dry they can be stored in a clean plastic container with a lid or
in a clean plastic sealed bag.
7.
Clean washing up bowl and bottle brush. Rinse them well and allow them to
air-dry after each use. Wash them by hand or in a dishwasher at least every
few days.
For daily sterilisation:
1.
Place clean parts in a pot and cover with water making sure there is room for
all of the parts to float freely in the pot.
2.
Bring the water to a boil and allow the parts to boil for 5 minutes.
3.
After boiling remove the parts from the pot with tongs and place on a clean
towel to dry, covering the parts with a second clean towel. Place washing up
bowl and bottle brush on a clean, unused tea towel or paper towel in an area
protected from dirt and dust. Do not use a tea towel to rub or pat items dry
because doing so may transfer germs to the items.
4.
Allow the parts to dry completely before assembly and use. Partially dried
parts may affect the operation of the pump.
3.3 Before Each Use
1.
Always wash and dry hands thoroughly with soap and water before handling
the breastmilk expression set.
2.
Before assembling the breastmilk expression set, be sure that all of the parts
are completely dry.
3.
Visually inspect the individual components for cracks, chips, tears,
discolouration or deterioration. These may affect the functionality of the pump.
4.
Inspect the tubing. If you find condensation in the air tube, wash and dry it
immediately or replace the tubing. If you see breastmilk inside the tubing or
tubing connectors do not attempt to wash, clean or sterilise the tubing or
tubing connectors. Instead contact the manufacturer.
5.
Should you have any questions or concerns about your parts please contact
Lansinoh® at
0113 259 1425
for further guidance.
6.
To purchase replacement parts for your pump please visit
lansinoh.co.uk/parts
