background image

 

Chapter 2  Hardware Description 

 

In  this  paragraph,  it  will  describe  the  Industrial  switch’s  hardware  spec,  port,  cabling 

information, and wiring installation. 

 

2.1  IP Protection 

The 

IP Code

Ingress Protection Rating

, sometimes also interpreted as 

International 

Protection Rating

, classifies and rates the degree of protection provided against the 

intrusion (including body parts such as hands and fingers), dust, accidental contact, and 

water in 

mechanical casings

 and with electrical enclosures. It is published by the 

International Electrotechnical Commission (IEC) 

 

Solid particle protection 

The first digit indicates the level of protection that the enclosure provides against access 

to hazardous parts (e.g., electrical conductors, moving parts) and the ingress of solid 

foreign objects. 

 

Level 

Object size 

protected against 

Effective against 

— 

No protection against contact and ingress of objects 

>50 mm 

Any large surface of the body, such as the back of a 

hand, but no protection against deliberate contact 

with a body part 

>12.5 mm 

Fingers or similar objects 

>2.5 mm 

Tools, thick wires, etc. 

>1 mm 

Most wires, screws, etc. 

Dust protected 

Ingress of dust is not entirely prevented, but it must 

not enter in sufficient quantity to interfere with the 

satisfactory operation of the equipment; complete 

Summary of Contents for IPGS-5 Series






























Reviews: