Lantronix EDS-MD Series Command Reference Manual Download

Page: 622 / 738

5: Commands and Levels

EDS-MD® Wired IoT Device Gateway Command Reference

622

domain

<text>

Sets the domain name. <text> = name of the
domain.

exit

Exits to the config level.

failover

Enter failover configuration level

hostname

<text>

Sets the host name. <text> = name of the host.

<instance>

Changes to the interface configuration level.

ip address

<ip address/cidr>

Sets the IP address and network mask. Formats
accepted: 192.168.1.1 (default mask)
192.168.1.1/24 (CIDR) "192.168.1.1 255.255.255.0"
(explicit mask)

link

Enter link configuration level

mtu

<bytes>

Sets the Maximum Transmission Unit (MTU) size.

no default gateway

Clears the default gateway.

no dhcp client id

Clears the DHCP client ID.

no domain

Clears the domain name.

no hostname

Clears the host name.

no ip address

Clears the IP address.

no primary dns

Clears the name of the primary DNS server.

no secondary dns

Clears the name of the secondary DNS server.

primary dns

<IP address>

Sets the IP address of the primary DNS server.

priority

<number>

Sets the priority for interface. <number> = priority
number.

secondary dns

<IP address>

Sets the IP address of the secondary DNS server.

show

Displays the current configuration.

show history

Displays the last 20 commands entered during the
current CLI session.

show status

Show interface status

state disable

Disables the interface.

state enable

Enables the interface.

write

Stores the current configuration in permanent
memory.

if 3 (config-if:eth2) level commands

bootp disable

Disables BOOTP.

bootp enable

Enables BOOTP.

clrscrn

Clears the screen.

default gateway

<IP address>

Sets the configurable gateway IP address to the
default value.

default mtu

Restores the default Maximum Transmission Unit
(MTU) size.

default priority

Restores the default priority for the interface.

dhcp client id

<text>

Sets the DHCP client ID.

dhcp disable

Disables DHCP.

dhcp enable

Enables DHCP.

domain

<text>

Sets the domain name. <text> = name of the
domain.

exit

Exits to the config level.

failover

Enter failover configuration level

hostname

<text>

Sets the host name. <text> = name of the host.

<instance>

Changes to the interface configuration level.

Summary of Contents for EDS-MD Series



































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for EDS-MD Series

Reviews:

Related manuals for EDS-MD Series

Brands by name

Popular brands

Lantronix EDS-MD Series, Command Reference Manual

Search results

Summary of Contents for EDS-MD Series

Reviews:

Related manuals for EDS-MD Series

Brands by name

Popular brands