Lantronix EDS-MD Series Command Reference Manual Download

Page: 691 / 738

5: Commands and Levels

EDS-MD® Wired IoT Device Gateway Command Reference

691

no password

Removes the password so connections will be
accepted unchallenged.

password

<text>

Sets the password required on the network side of
the tunnel to begin a connection.

prompt disable

Inhibits any prompting for password on the network
side of the tunnel.

prompt enable

Sets up so a user on the network side of the tunnel
will be prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the
current CLI session.

write

Stores the current configuration in permanent
memory.

password (tunnel-accept-password:7) level commands

clrscrn

Clears the screen.

exit

Exits to the next higher level.

no password

Removes the password so connections will be
accepted unchallenged.

password

<text>

Sets the password required on the network side of
the tunnel to begin a connection.

prompt disable

Inhibits any prompting for password on the network
side of the tunnel.

prompt enable

Sets up so a user on the network side of the tunnel
will be prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the
current CLI session.

write

Stores the current configuration in permanent
memory.

password (tunnel-accept-password:6) level commands

clrscrn

Clears the screen.

exit

Exits to the next higher level.

no password

Removes the password so connections will be
accepted unchallenged.

password

<text>

Sets the password required on the network side of
the tunnel to begin a connection.

prompt disable

Inhibits any prompting for password on the network
side of the tunnel.

prompt enable

Sets up so a user on the network side of the tunnel
will be prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the
current CLI session.

write

Stores the current configuration in permanent
memory.

password (tunnel-accept-password:5) level commands

clrscrn

Clears the screen.

exit

Exits to the next higher level.

Summary of Contents for EDS-MD Series



































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for EDS-MD Series

Reviews:

Related manuals for EDS-MD Series

Brands by name

Popular brands

Lantronix EDS-MD Series, Command Reference Manual

Search results

Summary of Contents for EDS-MD Series

Reviews:

Related manuals for EDS-MD Series

Brands by name

Popular brands