2
5. RUN QUICK SETUP TO CONFIGURE NETWORK (IP) SETTINGS
© 2019 Lantronix, Inc.
Lantronix
is a registered trademark, and
EMG
is a trademark of Lantronix, Inc. All other trademarks are the
property of respective owners. Specifications subject to change without notice. 895
-
0004
-
00
Contact Technical Support
For technical support queries, visit
http://www.lantronix.com/support
or call (800) 422
-
7044 Monday – Friday from 6:00 a.m. – 5:00 p.m.,
Pacific Time, excluding holidays.
Latest Firmware
For the latest firmware downloads, visit
http://www.lantronix.com/support/downloads
6. LOGGING IN TO THE WEB PAGE
To set up the network connections, you may do one of the following:
Complete the Quick Setup on the Web Manager.
SSH to the command line interface and follow the Quick Setup
script
Connect a terminal to the console (RS
-
232) port and follow the
Quick Setup script on the command line interface
The Quick Setup script lets you configure the Eth1 network settings,
change the date and time, and change the sysadmin password.
After you save the values for your EMG, the changes take effect
immediately.
7. LOGGING IN TO THE COMMAND INTERFACE
You can use either the Web Manager or the command line interface to
configure all parameters.
To log in to the EMG 8500 web page:
1. Open a web browser (Firefox, Chrome, Safari, or Internet Explorer
with the latest browser updates).
2. In the URL field, type
https://
followed by the IP address of your
EMG.
3. At the first login, enter
sysadmin
(all lower case) as the user and
PASS
(all upper case) as the factory default password.
Note:
Change the default password as soon as possible to prevent
access by unauthorized personnel.
The first time you log in, the EMG 8500 Quick Setup page is displayed.
Subsequent logins will display the EMG 8500 Home Page.
To access the command line interface:
1.
Do one of the following:
•
With a network connection, use a Telnet or SSH program to Telnet or
SSH to
xx.xx.xx.xx
(the IP address in dot quad notation), and press
Enter
. You should be at the login prompt.
Note:
By default, Telnet is disabled. To enable it, use the Services web
page, a serial terminal connection, or an SSH connection with a serial
terminal connection. When the command line displays, press
Enter
.
2. Enter
sysadmin
as the user name and press
Enter
.
3. Enter
PASS
as the password and press
Enter
. The first time you log in,
the Quick Setup script opens automatically. Subsequent logins display
the command prompt only.
Note:
Change the default password as soon as possible to prevent access
by unauthorized personnel.
4. If the Quick Setup script displays, update basic network parameters, as
desired. Otherwise, just press
Enter
until the command prompt dis-
plays. By pressing
Enter
, you are accepting the current settings.
Notes:
For general command line interface help, type “
help command
line
”.
For help with a specific command, type “
help”
followed by the command;
for example, “
help set network”
or “
help admin firmware”
.
4. IP ADDRESSING
Both of the EMG 8500 network ports (Ethernet 1 and Ethernet 2) de-
fault to DHCP–assigned IP addresses. If you want to assign a different IP
address, it must be within a valid range, unique to your network, and
use the same subnet mask as your workstation.
To configure the EMG 8500, you need the following information:
IP address (if not already assigned): ______ . ______ . ______ . ______
Subnet mask (if not already assigned): ______ . ______ . ______ . ______
Gateway: ______ . ______ . ______ . ______
DNS: ______ . ______ . ______ . ______
EMG
™
8500 Quick Start Guide
Edge Management
Gateway
Note:
To access the web page or to access the command line interface
using SSH or Telnet, the EMG unit must have a network connection and IP
address.
Note:
You can view the IP address by running the Lantronix Provisioning
Manager (LPM) application. Download LPM from
instructions in the user guide to discover devices.
4. Do one of the following:
•
To bypass the Quick Setup page and go directly to configuring the
EMG, click the
Accept default Quick Setup settings
checkbox and click
Apply
.
•
Update the basic network parameters, if desired, and click
Apply
.
After you save the values for the EMG unit, the changes take effect
immediately.
