Lantronix SGX 5150 Command Reference Manual Download

Page: 86 / 372

5: Commands and Levels

SGX™ 5150 IoT Device Gateway Command Reference

no email disconnect

Discontinues sending email alerts upon closing a connect mode tunnel.

promote host

<number>

Promotes the identified host, exchanging it place with the host above it, to adjust the order

of the defined hosts.

reconnect time

<millisec-

onds>

Sets the reconnect time value for tunneling connections established by the device in milli-
seconds. <milliseconds> = timeout in milliseconds.

show

Displays the current configuration.

show history

Displays the last 20 commands entered during the current CLI session.

show status

Displays tunnel connect status.

start character

<control>

Sets the connect mode start character. The character may be input as text, control, deci-

mal, or hex. A control character has the form <control>C. A decimal value character has
the form \99. A hex value character has the form 0xFF.

write

Stores the current configuration in permanent memory.

connection 1 (config-mach10-connection:1) level commands

clrscrn

Clears the screen.

default host

Restores the Hostname or IP address of Mach 10.

default local port

Clears the local port for Mach10 client.

default mqtt host

Restores the Hostname or IP address of MQTT server.

default mqtt local port

Clears the local port for Mach10 MQTT client.

default mqtt port

Restores the Port of MQTT server.

default port

Restores the Port of Mach 10.

default proxy port

Restores the Port of proxy server.

default proxy type

Restores the default Proxy server type (SOCKS5).

exit

Exits to the next higher level.

host

<text>

Sets the Hostname or IP address of Mach 10.

local port

<number>

Sets the local port for Mach10 client. When configured, a total of 16 consecutive ports will
be reserved.

mqtt host <

text

Sets the Hostname or IP address of MQTT server.

mqtt local port <

number

> Sets the local port for Mach10 MQTT client. When configured, a total of 32 consecutive

ports will be reserved.

mqtt port <

number

Sets the Port of MQTT server.

mqtt security disable

Disables SSL for MQTT.

mqtt security enable

Enables SSL for MQTT.

mqtt state disable

Disables MQTT.

mqtt state enable

Enables MQTT.

no proxy host

Restores the Hostname or IP address of the proxy server.

no proxy password

Restores the password for proxy server.

no proxy username

Clears the user name for the proxy server.

port

<number>

Sets the Port of Mach 10.

proxy host <

text

Sets the Hostname or IP address of the proxy server.

proxy password <

text

Sets the password the proxy server.

proxy port <

number

Sets the Port of the proxy server.

proxy type socks5

Sets the Proxy server type to SOCKS5

proxy username <

text

Sets the user name for the proxy server.

secure port disable

Disables HTTPS for Mach10 client.

secure port enable

Enables HTTPS for Mach10 client.

show

Shows the current configuration.

Summary of Contents for SGX 5150





















































































































































































































































































































































































Search results

Summary of Contents for SGX 5150

Reviews:

Related manuals for SGX 5150

Brands by name

Popular brands

Lantronix SGX 5150, Command Reference Manual

Search results

Summary of Contents for SGX 5150

Reviews:

Related manuals for SGX 5150

Brands by name

Popular brands