background image

11

Copyright LapSafe® Products

The Traveller™ Charge & Sync Range - User Manual

Should a host laptop/PC be connected for syncing, either at ‘switch on’ or during 
the charging period, a 

green

 light will flash slowly until one or more devices begin 

to synchronise. Devices will only begin to synchronise once they are fully charged 
and the Traveller™ will return each device to the charge status to maintain 
optimum readiness approximately an hour after syncing commences.

To override the ‘Full Auto’ mode, press the mode button on the power 
management unit as described in 

section 6.

6. Syncing

The LapSafe® Traveller™ is supplied with a USB A to USB B lead for connecting to a 
host PC or laptop 

(Figure 16)

.

Sync – (synchronising) describes an automatic process that is performed by the 
software on a computer when it is connected to another computer.  This is usually 
between a ‘Host’ computer and a ‘Slave’ computer, or a number of ‘Slave’ 
computers, for the purpose of having the data on all devices the same or 
synchronised.

Apple iTunes is the syncing software that facilitates all communications between 
the host PC or laptop and the iPads. For more information on iTunes visit: 
www.apple.com/itunes.

When synchronising software is not present the USB charge & sync case operates 
as a USB hub, allowing ‘drag and drop’ access to the device drives.

Connect the USB B end of the connector lead into the power management unit 
and plug the USB A end of the lead into a suitable port on the host PC. The 
connection will be detected by the power management unit and will react 
according to the mode of operation selected.

Summary of Contents for Traveller series

















Reviews: