sirio
Ediz. 006 - 12/2017
www.larius.eu
5
Read this operator’s manual carefully before using the equipment.
An improper use of this machine can cause injuries to people or things.
Do not use this machine when under the influence of drugs or alcohol.
Do not modify the equipment under any circumstances.
Use products and solvents that are compatible with the various parts of the equipment, and read the manufacturer’s warnings
carefully.
See the Technical Details for the equipment given in the Manual.
Check the equipment for worn parts once a day. If any worn parts are found, replace them using ONLY original spare parts.
Keep children and animals away from work area.
Comply with all safety standards.
It indicates an accident risk or serious damage to equipment if this warning is not followed.
It indicates important recommendations about disposal and recycling process of products in accordance with the environmental
regulations.
WArNINGs
The table below provides the meaning of the symbols used in this manual in relation to using, earthing,
operating, maintaining, and repairing of this equipment.
It indicates wound and finger squashing risk due to movable parts in the equipment.
Tenersi lontano dalle parti in movimento.
Do not use the equipment without the proper protection.
Before any inspection or maintenance of the equipment, carry out the decompression procedure explained in this manual, and
prevent any risk of the equipment starting unexpectedly.
Report any risk of chemical reaction or explosion if this warning has not been given.
There is a risk of injury or serious lesion related to contact with the jet from the spray gun. If this should occur, IMMEDIATELY
contact a doctor, indicating the type of product injected.
Do not spray before the guard has been placed over the nozzle and the trigger on the spray gun.
Do not put your fingers in the spray gun nozzle.
Once work has been completed, before carrying out any maintenance, complete the decompression procedure explained in
this manual.
This symbol signals the presence of a terminal with a grounding cable.
Use ONLY three-wire extensions and electrical outlets with grounding connections.
Before beginning work, make sure the electrical system is equipped with a grounding connection and that it complies with the safety
regulations.
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin.
To help prevent injection, always:
- Engage trigger lock when not spraying.
- Do not put your hand over the spray tip. Do not stop or deflect leaks with your hand, body or other.
- Do not point gun at anyone or at any part of the body.
- Never spray without tip guard.
- Ensure the trigger is locked at the end of spraying procedure.
- Do pressure relief at the end of spraying procedure and before any service operation.
- NEVER use components whose operating pressure is below the Maximum Working Pressure.
- Never allow children use this unit.
- Pay close attention to the possible recoil during gun triggering.
If high pressure fluid pierces your skin, the injury might look like “just a cut”, but it is a serious wound! Get immediate medical attention.
It is obligatory to wear suitable clothing as gloves, goggles and face shield.
Wear clothing that complies with the safety standards in force in the country in which the equipment is used.
Do not wear bracelets, earrings, rings, chains, or anything else that may hinder the operator’s work.
Do not wear clothing with wide sleeves, scarves, ties, or any other piece of clothing that could get tangled up in moving parts of
the equipment during the work, inspection, or maintenance cycles.
FIRE AND EXPLOSION HAZARD
Solvent and paint fumes in working area can ignite or explode.
To help prevent fire and explosion:
•
Use equipment ONLY in well ventilated area.
•
Eliminate all ignition sources, such as pilot lights, cigarettes and plastic drop cloths (potential static arc).
•
Ground equipment and conductive objects.
•
Use only grounded airless conductive hoses.
•
Do not use trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such
solvents in pressurized aluminium equipment. Such use can cause serious chemical reaction and explosion.
•
Never clean when the electrostatic parts of the gun are ON. Turn on the electrostatic parts of the gun only after having
removed any solvent from the circuit.
•
Use cleaning solvents with a flash point as high as possible, preferably higher than ambient temperature
If electrical shocks or discharges are encountered,
immediately stop
the operation of the equipment.
Keep a fire extinguisher at hand close to the working area.
0
Summary of Contents for Sirio 27:1
