Ed 004 - 06/2013
• KEEP YOUR WORK PLACE CLEAN AND TIDY. DISORDER
WHERE YOU ARE WORKING CREATES A POTENTIAL
RISK OF ACCIDENTS.
•
ALWAYS KEEP PROPER BALANCE AVOIDING UNUSUAL
STANCE.
•
BEFORE USING THE TOOL, ENSURE THERE ARE NOT
DAMAGED PARTS AND THE MACHINE CAN WORK PRO-
PERLY.
• ALWAYS FOLLOW THE INSTRUCTIONS ABOUT SAFETY
AND THE REGULATIONS IN FORCE.
•
KEEP THOSE WHO ARE NOT RESPONSIBLE FOR THE
EQUIPMENT OUT OF THE WORK AREA.
•
NEVER
EXCEED THE MAXIMUM WORKING PRESSURE
INDICATED .
•
NEVER
POINT THE SPRAY GUN AT YOURSELVES OR AT
OTHER PEOPLE . THE CONTACT WITH THE CASTING
CAN CAUSE SERIOUS INJURIES.
•
IN CASE OF INJURIES CAUSED BY THE GUN CASTING,
SEEK IMMEDIATE MEDICAL ADVICE SPECIFYING THE
TYPE OF THE PRODUCT INJECTED.
NEVER
UNDERVA-
LUE A WOUND CAUSED BY THE INJECTION OF A FLUID.
•
ALWAYS DISCONNECT THE SUPPLY AND RELEASE THE
PRESSURE IN THE CIRCUIT BEFORE PERFORMING ANY
CHECK OR PART REPLACEMENT OF THE EQUIPMENT .
•
NEVER MODIFY ANY PART IN THE EQUIPMENT. CHECK
REGULARLY THE COMPONENTS OF THE SYSTEM. RE-
PLACE DAMAGED OR WORN PARTS..
•
TIGHTEN AND CHECK ALL THE FITTINGS FOR CONNEC-
TION BETWEEN PUMP , FLEXIBLE HOSE AND SPRAY
GUN BEFORE USING THE EQUIPMENT.
•
ALWAYS USE THE FLEXIBLE HOSE SUPPLIED WITH
STANDARD KIT. THE USE OF ANY ACCESSORIES OR
TOOLING OTHER THAN THOSE RECOMMENDED IN
THIS MANUAL, MAY CAUSE DAMAGE OR INJURE THE
OPERATOR.
•
THE FLUID CONTAINED IN THE FLEXIBLE HOSE CAN
BE VERY DANGEROUS . HANDLE THE FLEXIBLE HOSE
CAREFULLY . DO NOT PULL THE FLEXIBLE HOSE TO
MOVE THE EQUIPMENT . NEVER USE A DAMAGED OR
A REPAIRED FLEXIBLE HOSE..
The high speed of the product in the hose can create
static electricity through discharges and sparks. It
is suggested to earth the equipment.
The pump is earthed through the earth cable of
the supply.
The gun is earthed through the high pressure
flexible hose.
All the conductive tools within the working area
must be duly earthed.
• NEVER SPRAY OVER FLAMMABLE PRODUCTS OR SOL-
VENTS IN CLOSED PLACES.
•
NEVER USE THE TOOLING IN PRESENCE OF POTEN-
TIALLY EXPLOSIVE GAS.
Always check the product is compatible with the
materials composing the equipment (
pump, spray
gun, flexible hose and accessories
) with which it
can come into contact. Never use paints or solvents
containing halogen hydrocarbons (
as the methy-
lene chloride
).
If these products come into contact with aluminium
parts can provoke dangerous chemical reactions
with risk of corrosion and explosion.
IF THE PRODUCT TO BE USED IS TOXIC, AVOID IN-
HALATION AND CONTACT BY USING PROTECTION
GLOVES, GOGGLES AND PROPER FACE SHIELDS.
TAKE PROPER SAFETY MEASURES FOR THE
PROTECTION OF HEARING IN CASE OF WORK
NEAR THE PLANT.
• WHENEVER YOU STOP DISPENSING, EVEN FOR A MO-
MENT, ALWAYS SET THE GUN TRIGGER LOCK. FULLY
RELEASE THE TRIGGER AND ROTATE THE TRIGGER
LOCK FORWARD (
see equipment description
).
• USE EXTREME CAUTION WHEN CLEANING OR CHAN-
GING THE FLUID NOZZLE. IF THE NOZZLE CLOGS
WHILE DISPENSING, FULLY RELEASE THE TRIGGER
IMMEDIATELY. ALWAYS FOLLOW THE PRESSURE RELIEF
PROCEDURE, BELOW, BEFORE WIPING OFF BUILD-UP
AROUND THE NOZZLE OR REMOVING THE NOZZLE TO
CLEAN IT.
www.larius.com
STAR 3001S GUN
9
