SPLED-QP-1X10WRE
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
2
of
3
Light weight lamps can be attached by tilting
quadpod
toward the ground with the legs up. Attach light head to pole, tighten hand
screw and tilt back to its vertical position. DO NOT tilt
quadpod
while extended to max height. It is recommended to have another
person hold the
quadpod
while tilting vertically.
For heavy weight lamps, use a ladder and extra help for attaching light head to pole.
Double check that all hand screws are tight before continuing use of the light tower.
EXTENDING
1.
Loosen hand screw for extending the light head. Once loose, extend light head until desired
height is achieved with at least
1ft - 2ft remaining inside pole for support.
WARNING:
DO NOT over extend light head completely allowing extension pole to free from base! If the light head becomes free,
serious injury or death can occur. Larson Electronics shall not be held liable for injuries caused by misuse.
2.
When desired height is achieved, tighten hand screw to secure light head.
LOWERING
1.
To lower mast, grasp light head and slowly loosen hand screw. Lower the light head and
tighten hand screw.
WARNING:
DO NOT loosen hand screw allowing light head to fall freely. This can damage the unit and cause serious injury or death.
Always grasp light head before lowering. Larson Electronics shall not be held liable for injuries caused by misuse.
The
quadpod
mount light tower can be disassembled for storage or transporting. Unplug light from power source and remove light head
following previous steps for attaching.
Once the light head has been removed, loosen hand screw for legs and fold them up. Wheel to desired location or remove from wheel
base for complete disassembly.
THE LENS AND CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, SCRATCHES OR ANY SEVERE ABRASIONS,
AND IF ANY ARE FOUND, THE PARTS MUST BE REPLACED BEFORE RESUMING USE OF THE LIGHT TOWER.
The EPL-QP-1X150RT series is designed to provide years of reliable lighting performance. Should the need for replacement parts arise,
please contact Larson Electronics at the contact information below.
OPERATION INSTRUCTIONS
1.
Unpack your new solar panel and beacon fixture.
2.
Mount solar panel on pole using the mount supplied with solar panel. This mount is designed to
mount over a pole ranging in diameter from 1”
to 2” and acts like a saddle around the pole.
Note:
Excessive force will cause the bracket to warp, hindering the mounting plate. This could
cause the mount to be loose and may not be mounted at the desired angle. Care should be
taken to not over tighten.
3.
For optimum performance of your new solar panel light, make sure it is positioned directly in
the sun with no shadows on the panel. Any
shading could affect the charging cycle and cut the
charge in half making the unit perform poorly.
4.
After mounting your new solar panel and assuring it is in the proper location
and angle, you are
ready to install the fixture. Care should be
taken when mounting your fixture and it should be
placed in an area not subject to damage.
Note:
Some fixtures supplied with this panel are class 1 division 2. This solar panel is not rated
for use in those areas and should be installed
outside the limits set by the NEC Code and local
authority having jurisdiction.)
5.
Once the fixture is installed, plug in the cord that is supplied with the solar panel to the fixture.
Make sure it snaps together firmly and is
latched. Once confirmed, you are ready for power.
6.
Turn the switch on the side of the solar panel from off to on. Your beacon should light up and
start operation. Some models come with an
option to change the strobe effect on the fixture. If
your fixture has this option there will be a rubber grommet on the side of the panel you can
open. Once opened, there will be a red button you can push. Each push will change the strobe
to a separate function.
Note:
Some versions come with a motion control and a photocell. If your unit is equipped with
either you will need to make sure the
environment matches the specifications before you test.
Note:
The on and off switch on the side of the unit is a battery disconnect, not a switch
for the
fixture. The battery disconnect protects the battery while the unit is not in operation.
7.
Set your desired strobe effect and seal back the access rubber.
