background image

L’ARTISTICO SRL  |  

EN

 

19

 

Cod. 40014 | Rev. 04 | 08/06/2018

 

 

• Never open the appliance door during operation. 

•  Do  not  operate  the  appliance  with  the  door  open  or  broken  or 
cracked glass. 

•  It  is  forbidden  to  operate  the  appliance  without  the  ash  drawer  (if 
fitted). 
• Avoid the formation of smoke and unburned during ignition and / or 

during normal operation, excessive buildup of unburned pellets in the 
brazier  must  be  removed  manually  before  proceeding  with  a  new 
ignition. 

• Warn children and guests of the above dangers. 
• In the event of anomalies, the product can only be restored after the 

problem has been restored. 
•  Do  not  turn  on  the  appliance  without  first  performing  the  daily 
inspection and cleaning as described in the MAINTENANCE chapter 

of this manual. 
• Carefully follow the maintenance program. 
•  Do  not  clean  the  stove  until  the  structure  and  ashes  cool  down 

completely. 
• Cleaning and maintenance to be carried out by the user must not be 

carried out by children without supervision. 
• Do not touch the generator if you are barefoot and wet or wet body 
parts. 

•  It  is  forbidden  to  modify  safety  or  regulation  devices  without  the 
manufacturer's approval or directions. 
• The appliance is connected to the mains by means of a plug,  this 

must be easily accessible with an installed stove. 
• Verify that the electrical system and sockets are of Norma and have 

the ability to withstand the maximum absorption of the appliance on 
the label and on the manual. 
•  It  is  recommended  to  position  the  power  cord  so  that  it  does  not 

come into contact with hot parts of the appliance. 
• Do not make any unauthorized changes to the appliance. 

• Use only original spare parts recommended by the manufacturer. 
• Do not leave packing items in the reach of children or unauthorized 
persons. 

•  After  a  long  period  of  non-use,  check  for  any  obstructions  before 
switching on the appliance. 
• The appliance is designed to operate under any weather conditions, 

in the event of adverse weather conditions (strong wind, frost), safety 
systems may be triggered by the generator switched off. If this is the 

case,  contact  your  service  representative  and,  in  any  case,  do  not 
disable security systems. 
• If there is a fire in the chimney, have adequate systems to suffocate 

the flames or request the intervention of firefighters. 
 
 

6.  DISPOSAL OF EQUIPMENT AND PACKAGING 

The waste bin symbol indicates that the product, at the 
end  of  the  life  cycle,  must  be  handed  over  to  the 

appropriate collection centers set up by municipalities or 
urban  hygiene  companies.  Properly  differentiated 

collection helps to avoid possible adverse effects on the 
environment  and  health  and  favors  the  recycling  of 

materials that are made up of the equipment. 

Disposal  of  Waste  Electrical  and  Electronic  Equipment 
(WEEE), pursuant to Legislative Decree 14 March 2014, 
no.  49  implementing  the  2012/19  /  EU  Directive  and 
WEEE on the disposal of waste electrical and electronic 
equipment. 

 
The packaging is intended to protect the goods from any damage that 
may  occur  during  transport  operations.  The  materials  used  for 

packaging  are  recyclable,  so  they  are  selected  according  to 
environmentally friendly and easy disposal methods for reintegration 
into  production  cycles.  Refer  to  applicable  local  disposal  regulations 

for all wood, board and plastic packaging materials. Do not dispose of 

any packaging or product in the environment. Keep packing materials 

out of the reach of children 

Correct disposal of the batteries in this product 

(Applicable in countries with separate collection systems) 

This  marking  on  battery,  manual  or  packaging 
indicates that the batteries in this product should not 
be disposed of with other household waste at the end 

of  their  working  life.  Where  marked,  the  chemical 
symbols  Hg,  Cd  or  Pb  indicate  that  the  battery 

contains mercury, cadmium or lead above the reference levels in EC 
Directive  2006/66.  If  batteries  are  not  properly  disposed  of,  these 
substances can cause harm to human health or the environment. 

To  protect  natural  resources  and  to  promote  material  reuse,  please 
separate batteries from other types of waste and recycle them through 

your local, free battery return system. 
 
 

7.  HANDLING AND STOCKING  

The cardboard/wood package has been designed to protect the stove 
but cannot be stocked in outdoor or in very damp places. It must be 

exposed  to  the  elements,  otherwise  some  components  or  the  stove 
itself could get damaged and the guarantee will decline. Since stoves 
have  some  sensitive  parts  like  glasses  and  electronic  components, 

should be handled following few basic rules: 
Lift and lay down the stove gently. In case you use a two wheel trolley 
or  when  transporting  upstairs,  always  take  the  stove  at  the  side 

opposite  to  the  glass  (which  is  identified  by  a  sticker).  The  glass  is 
always on the sticker side. 

 

 
 

8.  AUTHORIZED FUEL 

Allowed fuels are firewood and pellets. Only dry wood logs (max. 20% 
water content) and pellets conforming to the characteristics described 
below must be used. 

 

PELLET 

Pellet  is  produced  with  wood  rests  from  clean  wood  machining  like 

sawmills, furniture manufacturing or new wood from forest culture. All 
these 100% vegetable materials are dried and pressed into the pellet 
form without adding any kind of glue or chemical. We do approve to 

be used in our stoves all pellets that satisfy the European regulation 
EN 14961-2. All the approved pellets must carry the following logo: 

   new logo since 2011

 

 WARNING: Use only Ø 6 mm pellets. 

Typical specifications for the approved fuel: 

Summary of Contents for Pellicano M14

































Reviews: