4
Instruction Manual
Cable and Bar Cutter “CC0040”
4. START UP.
MODELS WITH IN-BUILT PUMP.
CC0018,CC0040 AND CC0075
MODELS WITH A SEPARATE PUMP.
CC0118, CC0140, CC0162, CC0175, CC0190 AND C01120.
1- Hold the tool by the thick handle and with the tool in an upright position (head
facing up.
1- Connect the hose’s female quick plug to the tool’s male plug. Make
sure the connection is secure.
2- Pump the lever to check that the blade moves forward.
2- Read and follow the pump instructions.
3- Make sure the deformation zone is free from obstruction, and then continue
pumping until the blade reaches the end of its travel. At this point the lever will
become stiffer and harder to move.
3- Remove the pin and open the tool head.
4-Continue pumping until the safety valve is activated. Check for oil leaks.
4- Place the material to be cut in the cavity of the counter-blade and
close the head, fixing it in place with the pin. Make sure the pin is
properly positioned.
5- Press the unload button and check that the blade returns to its initial position.
5- Pump until the material is cut.
6- Repeat this operation as many times as necessary in order to become familiar
with the operation of the tool.
6- Move the blade back activating the pump valve.
7- Remove the pin and open the tool head.
7- Pump until the material is cut.
8- Place the material to be cut in the cavity of the counter-blade and close the
head, fixing it in place with the pin. Make sure the pin is properly positioned.
8- When using electric or air-based pumps, the application is
automated. In such cases, the operator should be specially trained, in
order to avoid the possibility of involuntary actions.
9- Pump until the material is cut.
10- Once cut, press the unload button to move the blade back. Open the head and
remove all traces of waste material before making another cut.
5. MAINTENANCE.
¾
After use, the tool should be cleaned and the area where the blade comes into contact with the heads oiled.
¾
In the event of oil leaks, disassemble the tool and change the seals. The individual blueprint provided for each tool specifies its components and codes.
¾
During this operation, check the condition of the inside of the cylinder. If scratches or snags are detected, then a more thorough repair procedure will be
required. We recommend that this be carried out
by specialist personnel
.
¾
Check for loose nuts in the head.
¾
In the event of improper functioning in the models with built-in pumps, we recommend that you send the tool to an authorised technical service for
inspection and repair.
CHANGING THE BLADE.
•
CC0018, CC0118, CC0075, CC0175, CC0190 and CC01120: pump until the piston and blade move out far enough to provide access to the screw (22). Release
the screw and remove the blade. Replace the blade with a new one and attach to the piston by tightening the screw (22) once again.
•
CC0040, CC0140 and CC0160: You do not need to pump the piston out, since in these models, the screw (22) can be accessed with the blade in its standby
position. Simply remove the screw (22) and replace the blade.
6. WARRANTY.
LARZEP, S.A.
guarantees its products against all design and manufacturing defects for the durations of two years from the date of purchase. This guarantee does
not include the ordinary wear of both metal and non-metal parts, abuse, using the equipment beyond its rated capacity and any wear or damage incurred as a result of
using a hydraulic fluid which is not recommended by
LARZEP, S.A.
Please note that if the equipment is disassembled or serviced by anyone other than an authorized service dealer or by
LARZEP, S.A
., this guarantee is rendered null
and void.
In the event of a warranty claim, return the equipment, to
LARZEP, S.A
. or the authorized dealer which sold you the hydraulic equipment,
LARZEP, S.A
. will
repair or replace the faulty equipment, whichever is deemed most appropriate.
LARZEP, S.A.
shall not be held liable for any consequential damages or losses,
which may occur as a result of faulty equipment
