OPERATION
This Fan may be operated by the Manual Controls located on top of
the unit (as shown in
Figure 5
) or by the Remote Control (shown in
Figure 6)
.
1. Place the Fan on a firm and level surface.
CAUTION:
Plastic or rubber tabs, like the feet on this unit, may
stick to furniture surfaces and/or hardwood floors. The unit may leave
a residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces,
and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may slip
partially or completely out of the receptacle with only
the slight movement of the attached cord. Receptacles
in this condition may overheat and pose a serious fire
hazard; if covered by a curtain or drape, the fire hazard
is even greater.
3. When the Fan is plugged in, there will be a “beep” to indicate there
is power to the unit.
4. Turn the Fan ON by pressing the
Power Button
( ). The Fan will
“beep” twice to indicate that the unit has been turned ON.
5.
SPEEDS:
Press the
Fan Speed Button
( ) to desired speed
setting. Each time the Fan Speed Button is pressed, the speed
will change from Low (1), to Medium (2), to High (3). When intially
plugged in, the Fan will be in Low Speed. When the Fan is turned
OFF and ON again, the unit will resume the speed at which it was
turned OFF.
6.
OSCILLATION:
Press the
Oscillation Button
( ) to start and
stop the oscillation function.
7.
TIMER:
The timer function allows the unit to be set to operate for
a length of time from 1/2 hour to 7 1/2 hours, in increments of 1/2
hour. Press the
Timer Button
( ) to set the length of time desired.
Each time the timer button is pressed, the time is increased by 1/2
hour. After reaching 7 1/2 hours, pressing the timer button once
more will reset the Fan to continuous running. The lights on the
front of the unit will light up appropriately with the length of time
that the Fan is set for.
8.
SLEEP:
This function allows the unit to be set in Sleep Mode.
Pressing the
Sleep Button
( ) once will set the unit on Low for 6
continuous hours. Pressing the
Sleep Button
( ) a second time
will reset the unit to 6 continuous hours. The Oscillation Button
( ) will function when the Fan is in Sleep Mode. Pressing any
other button (Timer, Fan Speed or the Power Button) will shut off
the Sleep Mode.
9. To turn the Fan OFF, press the
Power Button
( ) and unplug the
unit from the electrical outlet.
MODEL 2530
Rev. F 9/07
4
2530WGES
Rev. F 9/07
9
2530WGES
MODELO 2530
Figura 3
Conjunto de la Base de Soporte
-
Vista des de Abajo
Conjunto
de la Base
de Soporte
#8 X 1/2"
Tornillos
Cable
Eléctrico
5. Fije los
Tornillos (2) #8 X 1/2"
en los cuatro orificios que se
encuentran en la parte inferior de la base.
(Figura 3)
6. Alinee el
Conjunto de la Base de Soporte
con el
Soporte de
Columna
, cerciorándose de que el canal del cable en la parte
inferior de la base de soporte esté orientado hacia la parte posterior
del Ventilador. Ensamble el
Conjunto de la Base de Soporte
con
el
Conjunto del Soporte de Columna
utilizando los
Tornillos M5
de (4) 1"
de largo. Jale con cuidado toda holgura excesiva del
Cable de Electricidad
e introdúzcala por el
Canal Conductor de
Cable
.
(Figura 4)
Conjunto de Columna Para la Base
M5 X 1"
Tornillos
Conjunto De
Soportes De
Columna
Cable
Eléctrico
Canal
Conductor
de Cable
Figura 4
Conjunto
de la Base
de Soporte
Figure 5
Remote Storage
Figura 1
Cable
Eléctrico
Canales Para
Cable
Soportes De
Columna
Base Del
Motor
Muesca
Localizadora
Tornillos
M5 de 1/2"
Conjunto De Soportes De Columna
Llave
Cable
Eléctrico
Figura 2
Base de
Soporte B
Base de
Soporte A
Copas
Conjunto de la Base de Soporte
-
Vista des de Arriba
Soportes De
Columna
ARMADO
1. Para facilitar el armado, recueste el Ventilador de modo que la
parrilla negra y el tablero de control den hacia arriba.
2. Localice el
Cable Eléctrico
en la parte inferior del Ventilador.
Coloque el
Cable Eléctrico
en los
Canales Para Cable
de los
Soportes De Columna
. Encaje firmemente los
Soportes De
Columna
el uno con el otro de modo de formar un
Conjunto De
Soportes De Columna
.
(Figura 1)
3. Una el
Conjunto De Soportes De Columna
a la
Base Del Motor
con
(4) Tornillos M5 de 1/2" de largo
. Cerciórese de alinear la
Llave
del
Conjunto De Soportes De Columna
con la
Muesca
Localizadora
de la
Base Del Motor
.
(Figura 1)
4. Arme las Bases de Soporte, introduciendo las
Copas
en la
Base
de Soporte A
en los
Orificios De Copas
de la
Base de Soporte
B
. Pase el
Cable de Electricidad
por el orificio grande en el centro
del Conjunto de la Base de Soporte.
(Figura 2)
4 por ventilador
4 por ventilador
2 por ventilador
Tamaño real de tornillos