background image

PC100 Terminal User’s Guide 

Specifications 

 

Casing: 

6.375”W x 7.375”H x 1.5”D flame-retardant ABS plastic. 19 oz. 
Includes key lock and wall mounting bracket 

 
Power: 

6VDC/ 300 mA wall-mount power supply.  UL approved 

 
Display: 

4 lines x 20 characters liquid crystal with large block digits 

 
Swipe 

“Beeper” signals good or bad badge reading and low memory. 

Status: 

Green and red LED’s show good or bad badge swipes 

 
Badge  
Reader: 

Mag-Stripe Track 2 reads standard “credit card” format 

 
Badges: 

Accepts badges #1-250. Badge metallic stripes are even-parity 

 
Memory: 

Stores about 1,500 registrations. Protected by internal 10-year 
lithium battery.  
 
This product’s lithium battery contains Perchlorate Material – 
special handling may apply. Please go to web site 
www.dtsc.ca.gov/hazardouswaste/perchlorate for information 
about proper methods of disposal in California. 

 
Ports: 

RS-232 cable at speeds of 1200, 2400, 4800 and 9600 baud 

 

For PC100-R: RS-485 Cat. 3 or Cat. 5 cable (suggested) at speeds 
of 2400, 4800 and 9600 baud. Up to 4000 feet 

 
Certifications: UL; C-UL; FCC Part-15 Class-B; Canada ICES-003 Class-B; 
 

CE-CENELEC EN55022; CENELEC EN55024 

Summary of Contents for PC100-R






















Reviews: