background image

PC3500TX Terminal Installation & User’s Guide - 13 

 

Press the ENTER key. The following message will be displayed: 

 

TCP/IP Conn. Mode 

 
Press the CLEAR key and select the Static option. 

 

Press the ENTER key. The following message will be displayed: 

 

Enter Socket Port # 

 

Enter 

02500

 followed by the ENTER key. The following message will be displayed. 

 

Enter Terminal IP  
###. ###. ###. ### 

 

This is the PC3500TX’s unique IP address. This must be a “Static” IP address that 
will be assigned by the network administrator. 
 
Enter the terminal’s numeric IP address followed by the ENTER key. The following 
message will be displayed: 

 

Enter Host IP 
###. ###. ###. ### 
 

This is the Host’s (PC that is running the Terminal Manager Module) unique IP 
address. (See your network administrator for assignment.) 
 
Enter the host’s numeric IP address followed by the ENTER key. The following 
message will be displayed: 

 

Default Router? 

 
Press the CLEAR key and select either Yes or No and press the ENTER key.  

 

If 

Yes

 was selected the following message will be displayed: 

 
Enter Router IP  
###. ###. ###. ### 

 

Summary of Contents for PC3500TX


































Reviews: