background image

Programming Cables  

User Guide 

© 2009-2019 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at 

www.latticesemi.com/legal

 

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 

FPGA-UG-02042-26.2 

 

13 

10.

 

Ordering Information 

Table 10.1. Programming Cable Feature Summary 

Feature 

HW-USBN-2B  HW-USBN-2A  HW-USB-2A 

HW-USB-1A 

HW-DLN-3C 

HW7265-DL3, 
HW7265-DL3A, 
HW-DL-3B, 
HW-DL-3C 

HW7265-DL2 

HW7265-DL2A  PDS4102-DL2 

PDS4102-DL2A 

USB 

— 

— 

— 

— 

— 

— 

PC-Parallel 

— 

— 

— 

— 

1.2 V Support 

— 

— 

— 

— 

— 

— 

— 

1.8 V Support 

— 

— 

2.5-3.3 V 
Support 

5.0 V Support 

— 

2 x 5 Connector 

— 

— 

— 

1 x 8 Connector 

 

— 

— 

Flywire 

— 

— 

— 

— 

Lead-free 
Construction 

— 

— 

— 

— 

— 

— 

— 

Available for 
order 

— 

— 

— 

— 

— 

— 

— 

— 

 

Table 10.2. Ordering Information 

Description 

Ordering Part Number 

China RoHS Environment- Friendly 

Use Period (EFUP) 

Programming cable (USB). Contains 6' USB cable, flywire 
connectors, 8-position (1 x 8) adapter and 10-position (2 x 5) 
adapter, lead-free, RoHS compliant construction. 

HW-USBN-2B 

 

Programming cable (PC only). Contains parallel port adapter, 6' 
cable, flywire connectors, 8-position (1 x 8) adapter and 10-
position (2 x 5) adapter, lead-free, RoHS compliant construction. 

HW-DLN-3C 

Note: Additional cables are described in this document for legacy purposes only, these cables are no longer produced. The cables 
currently available for order are fully equivalent replacement items. 

 

 

Summary of Contents for HW-USBN-2B






















Reviews: