background image

Programming Cables 

 

 

User Guide 

 

© 2009-2019 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at 

www.latticesemi.com/legal

 

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 

 

FPGA-UG-02042-26.2 

Disclaimers 

Lattice makes no warranty, representation, or guarantee regarding the accuracy of information contained in this document or the suitability of its 
products for any particular purpose. All information herein is provided AS IS and with all faults, and all risk associated with such information is entirely 
with Buyer. Buyer shall not rely on any data and performance specifications or parameters provided herein. Products sold by Lattice have been 
subject to limited testing and it is the Buyer's responsibility to independently determine the suitability of any products and to test and verify the 
same. No Lattice products should be used in conjunction with mission- or safety-critical or any other application in which the failure of Lattice’s 
product could create a situation where personal injury, death, severe property or environmental damage may occur. The information provided in this 
document is proprietary to Lattice Semiconductor, and Lattice reserves the right to make any changes to the information in this document or to any 
products at any time without notice. 
 

Summary of Contents for HW-USBN-2B






















Reviews: